Interior door type is not only a heat and noise insulating device, but also a full-fledged decorative room detail, which is designed to decorate the interior. It is no secret that this factor is of the initial value when installing a certain cost of products from the manufacturer. Often the most favorite door happens on the pocket not everyone, but everyone wants to change the appearance of the door that worn out for a long period of operation.
Alkyd paints are most popular for painting interior doors.
In this case, it is recommended to update the door with your own hands. If you have a good imagination and you are not alien to creative gusts, you will easily be able to change the idle of the interior door yourself, as it does not require professional skills. Below are several methods of updating and decorating doors. Before starting work, it is worth considering that you have to do the trim of doorways and slopes.
Preparatory work
Whatever the update method is applied, the coating of each door needs to be prepared. The following accessories will be required to work:
- Construction glue mix;
- tracing;
- Press (any massive object fit).
First of all, it is necessary to dismantle the door or remove it, after which it is good to study on the subject of scratches, irradiated sites and cracks.
The door can be separated by a rolled material with an image of exotic plants.
It is necessary to carefully apply an adhesive mixture into the places, apply on top of the cushion and press well with the press.
Microscopes and cracks can be filled with the same adhesive mixture. If the gaps are big, you will have to make some efforts to carefully close them.
At the same time, fine chips should be added to the glue composition.
Methods of updating doors
The most simple methods of updating the door canvase are the following:- staining;
- varnish coating;
- boring;
- veneering;
- decoration pattern or pattern (decoupage);
- Decorative cracks (cracker).
Coloring, varnishing, filling and veneering
Vacuation is best carried out with a brush, as it is well crossed by hard-to-reach areas.
Painting is the most common method of finishing interior doors. In the process of updating the outside of the web, organic, synthetic or water varieties of dyes are used. As a result, the door acquires a fresh appearance and looks like new. The paint is selected based on the material of the door leaf and its color.
For varnishing of the door leaf, a varnish for wooden products or protective and decorative lacquer varnish is usually used. Wood varnishes are perfectly absorbed into the structure of the canvas, evenly covering its surface. The main advantage of protective and decorative varnish is a toning basis that gives the door a rich appearance.
Article on the topic: How beautiful to collect curtains: basic methods
The varnishing is carried out using a brush or sprayer, but it is recommended to use the first option, because when applied, the brush repeats the contours of the web and cries well-to-reach areas. To increase protective properties, it is best to apply lacquer in 2 layers.
The veneer of the interior doors gives the canvas expensive and aesthetic appearance.
If the interior door is not updated for the first time, resort to the processing method using a simulator, after which the surface is lacquered. The simulator also applies if you want to update the color gamut of the web. It does not allow a new shade to mix with the old, and the subsequent varnish enhances the brightness of the selected color. If you depart the finished canvas, it will acquire a matte tint. In the absence of the need to achieve matte color after grinding, you need to polish the surface of the door and dry it. Thus, the door canvas will acquire crystal shine and becomes like absolutely new.
This method is most often discharged by very old samples of the canvas, which were made from sawdust of cheap and recycled logs. Sampling will allow such a canvas expensive and aesthetic appearance. The main thing is to handle the surface of the door well and polish it carefully. The sticking of the veneer is performed transversely in relation to the wood fiber.
Vinyl self-playing
Options for ready-made vinyl stickers for doors.
In the absence of a desire to spend a lot of time and tools for updating the door, you can use the vinyl self-taking for wood. This method will not require special skills from you, it will easily hide all the defects of the canvas and give it a fresh appearance. The following materials will be needed for work:
- piece of fabric;
- household hair dryer;
- scissors.
The canvas is updated within a few minutes. It is worth considering that before sticking, it is necessary to carefully clean its surface.
Cross the self-keeper and carefully remove the protective layer. The vinyl sticker is pasted on the principle of wallpaper canvas, that is, it should be smoothed with a rag to prevent the formation of bubbles. After 8-10 minutes, it is necessary to remove the film from the coating of self-keys. If this process causes you difficulties, heat the sticker with a hairdryer. This will help remove the film without any difficulty.
Decoration pattern or pattern
Decoupage Door is carried out on a thoroughly washed and dry surface.
The technology for decorating the door leaf will also not require special skills. Decoupage can be carried out even without dismantling the door, it will only need to rinse thoroughly and dry it.
Before you start work, you must go to the doorway by mounting scotch. The canvas need to be highly primed, grate with a simple paraffin candle and paint. After that, proceed to sticking decoupage cards, but at first they will need to soak in water for 8-12 minutes. Before cutting a drop of water, it is necessary to wipe with a dry cloth, after which it is careful to cover the back of the cards and the surface of the PVA door glue.
Article on the topic: How to make curtains from beads and durable fishing line?
Tightly gluing each item, you need to check if there are bubbles or folds. If you cannot eliminate them immediately, it will be enough to correct defects in the future. After drying, a thin layer of putty is applied to the edge of the card. Its excess can be removed by eats or wet cloth. If you wish, you can handle the door edges, leaving losses there. It will give the canvas vintage style.
There is an alternative decoring option. The door leaf is decorated with details of various shapes, which are cut from napkins. The color scheme is selected under the interior shades. The process of sticking is similar to the above described. Upon completion of the work, the door is covered with acrylic varnish.
Decorative cracks
Table with basic and finishing coatings.
This method of updating the door canvase is the most original. He will have to do with people who with trepidation belong to old things. In addition, such a decor is rare enough, which gives him individuality. Collecture application technology implies two-layer lacquering of the door canvase. An important point is the selection of varnish - each layer must have a different composition and drying time. Before finishing, you need to thoroughly clean, degrease and dry the door coating.
The following materials will be needed for work:
- Special crochelle varnish;
- Bitumen varnish for the booming effect;
- Acrylic paint.
First of all, the craklery varnish is applied to the canvas. As soon as the 1st layer serves, a bitumen varnish is applied on top of it with a 2nd layer. It is used to strengthen the contrast effect if a white background is selected. For dark tones, it is advisable to use acrylic paint. This method is considered the best.
If you have difficulties with the purchase of crochelle varnish, it can be replaced by the usual PVA glue, gelatin, vinegar or egg protein.
Incruitment of the door leaf and stained-in painting
For stained glass design, the door will require a special type of water colors and the outline of the desired pattern.
People who have the skill of processing wooden materials refer to the update methods more complicated. The main materials for the marquetry, inlative and intars of door canvases are the following:
- Leather Products;
- Glass and mirror tiles;
- stained glass
- mat;
- bamboo curtains;
- Wood bars;
- veneer.
The decoration process requires some experience, amazing and connecting imagination. The final result will be not only the original decor, but also the interior compliance according to your taste.
The canvas, where the simple glass tile is replaced with stained glass, creates an extraordinary view in the interior of the room. To embody this idea of life, you will need a special type of water colors and the outline of the desired pattern. Your task is to transfer the pattern to the door glass with paint. This procedure is performed in the following order:
- The drawing sketch is prepared on ordinary paper.
- The processed glass is thoroughly cleaned and degreases.
- The drawing is substituted with the glass and carefully will be burned on the back of a thin brush.
- The circular circuits are painted by various colors of paints at your discretion.
Article on the topic: Milan doors color: Photo in the interior
Upon completion of the painting process, it is necessary to give paint to dry over 20-22 hours. After drying, the glass fragment is inserted back into the door cloth and is well fixed.
Upgrading doorways
Diagram of the doorway doorway panels MDF.
After successfully updating the canvas, you must take care of the doorway, otherwise the beautiful door will be in it at all at all to the place. For the successful performance of the upcoming work, it is necessary to gradually plan the finish process.
First of all, reference guides will be necessary. In the future, they can be repainted by the color of the door canvase. If the guides were strongly extended, the plasterboard trim can be mounted on top of them. If there are irregularities and roughness, the trim need to be equipped with special perforated corners. After that, the opening can be repainted.
At the end of the renewal of the opening on its perimeter, it is necessary to properly place the platbands. It is recommended to secure on special locks that hold the platband well. If the locks are missing, the bar is glued using a special adhesive or screwed on screw screws.
Updating door slopes
Wooden door slope diagram.
If the slopes of interroom doors are not converted in accordance with the updated opening and door web, the update cannot be considered completed. Sucks are separated by various methods, several of them are described below.
The most common update method is the installation of ready-made MDF-based slopes. The second most popular method is considered to install drywall slopes that are attached to glue or perforated corner.
Another finishing method is the stucco of slopes. This method is considered the most time consuming and will require a certain time to fulfill all the work. Practice shows that the best option is peer-plaster slings, but they will require some costs of building materials. But the final result will be high-strength and durable slopes with increased resistance to the formation of mold.
The modern market offers many variants of decorative slopes, among which you can choose what comes to your new door.
Updating the door, its opening and slopes - a fairly elementary process that does not always require professional skills. With a great desire and low cost, you can turn the usual door to the work of art. The main thing is to include imagination and allocate some free time.