What sizes have sliding doors. How to calculate the desired size correctly. Always remain a popular solution in the interior of sliding doors.
They have advantages over the swap design, because they allow you to save place in the room, can block the entrance of any size, and at the same time have a stylish design. There are interroom products of standard parameters, as well as manufactured by an individual project.
Standard models
Roto
The installation process of standard door groups depends on the planning of the apartment. In such cases, it is recommended to purchase a specific model among the range of assortment. Standard are the parameters 600/700 / 800x2000 / 2100 mm wide and height, respectively. According to GOST, the cloth width in 600-800 mm and a height of 2000-2100 mm are suitable for opening 640-840 mm wide and 1976-2076 mm in height.
For passes width from 1145 to 1745 mm, it is necessary to select an option from two or more segments. The width of the shifting flaps is 110-170 cm, and each sash separately is 60-90 cm. If the dimensions of the opening are much more specified, the design consisting of a larger number of sesters is used. However, such interroom models are manufactured by individual order.
There are several types of sliding door groups with sash:
coupe
- movable parallel wall;
- incoming inside the wall;
- folded to the parties;
- Committed one for another.
One of the most interesting options is the folding system. The general parameter varies depending on how many panels are attached. Typically, the width of one such segment is 10-20 cm. The dimensions of the standard opening make it possible to install sliding sash that may include 5-7 canvases.
The table of structures of standard dimensions (in mm) will allow you to correctly select the cloth to the desired parameters.
| Height | 1900. | 1900. | 2000. | 2000. | 2000. | 2000. |
| Width | 550. | 600. | 600. | 700. | 800. | 900. |
Article on the topic: Falish Windows: Features, Production Rules
Installation is usually carried out without additional fasteners. As a rule, the difference between the parameters of the canvas and the opening is 150 and 100 mm. The remaining lumens are usually poured foam, and the whole design is trimmed with plasterboard. It is equipped with a sliding mechanism including carriage and rollers.
Non-standard dimensions of entrance groups
There are cases when you need to put the doors with non-standard height and width parameters. To this end, manufacturers make the design under certain parameters of the opening. During the development process, not only the height and width of the product are taken into account, but also its design, which would fit into the overall interior. The project can be compiled by an experienced designer or submitted by the customer themselves, in accordance with his vision of the result.
In most cases, interior doors on an individual project are performed manually, especially if the sliding flaps should repeat the outline in the form of the arch. In the process of manufacturing such structures, it is necessary to spend more time than when creating standard products with specific GOST dimensions.
Such options can be used not only as input groups in the room, but also as:
harmonic
- Wardrobe fence,
- partition in the middle of the room,
- Doors of the cabinet-niche.
Doors are installed in the process of restoration of the old room. Previously, the construction of houses did not adhere to specific standards, therefore, in each individual house there could be their sizes. In the process of creating, such factors such as coating and surface color are taken into account, since perfectly selected components are able to superbly complement the interior of the room.
Features of calculation
To perform calculations in the design of products according to an individual project that have non-standard dimensions, the following parameters should be:
Features of calculation
- the length of the platbands;
- the thickness of the island;
- height and width of the product;
- Availability / absence of a threshold.
To determine the sizes that sliding interior doors must be taken, you should use the following formula:
Article on the topic: Installation and fastening the bath to the wall do it yourself
Width of the opening + 2x power of the box + 2 poz for mounting.
Most often, the wall thickness is 7.5 cm. Wider openings should cover bivalve sliding doors. Their width is more than 1 meter, and this parameter affects the choice of material for the design, since its weight is much larger than that of standard options for input door groups. The optimal project includes two interroom panels, one of which is snapped with a spinlet. Thus, one sash is usually used, but if you need to increase the size of the passage, the second one opens.
size table
To install the input groups correctly, you need to take into account such moments:
- The input must contain only direct angles (if it is standard), its height should be the same at all points. The entrance lines must be exactly parallel to each other.
- All contours must be smooth, without protruding corners and bricks.
- The walls on both sides of the passage should be located strictly in the same plane and not to have narrowings (this can be checked long bar). The maximum permissible distinction on both of these criteria is not more than 3 mm.
- Before the start of installation, the existing plinth dismantle, and set it after the end of the work.
(Your voice will be the first)
Loading…