The door box is mostly frame that contains bars and false. Strengthen the box with special bolts or use steel overlays.
Door box can be collected with their own hands using wooden bars and fasteners.
To prevent irregularities while setting the box, use a plumb and level. In the case of stone walls, the box is attached to wooden tubes using nails. If the walls consist of plates, the designs will be held only on brackets.
Self-making boxes
In order to understand how to make the door frame with your own hands, you need to familiarize yourself with some points of the work itself.
For the beginning, dimensions are removed. There are 2 data removal methods:
- on the doorway;
- on the installed door.
For example, the calculation of the data on the acting door. First, the sides are measured, they have been replaced with 5 cm from all sides of the door. Next, you measure the threshold and the upper part of the system, leaving the place for the allowance. Then they calculate the metrah and start sawing.
Next fold bars to the floor, they will be needed when laying a side box. They should lie by level, grooves from above. The upper and lower boundaries of the future door are celebrated, while the threshold thickness is added. From bars that are applied to the threshold and crossbar are made of certain serifs so that the sawing line is visible.
Scheme of removal of measurements of the doorway.
Then cut the prepared materials for collecting. After cutting, the blanks need to be adjusted to the appropriate size. In one of the billets make a slot of future loops, applying a chisel and a hammer. Before you begin to do, you need to know the desired side opening side.
To continue an independent assembly, you need to use screws and nails for the strength of the future design. Next hinges are hung and strengthen the doorway. Align the gaps.
Article on the topic: Private house lighting - 100 photos of the perfect combination
Required tools that will help collect the door, it is:
- construction knife;
- Corolnic;
- roulette;
- pencil;
- a hammer;
- screwdriver;
- plane;
- hacksaw.
Use a set of screwdrivers of different configurations, use pliers, scrap, small-sized nails.
For breakdown holes in concrete, a perforator is necessary. Prepare materials for the door will be able to fine-saw. It makes a lot of electric milling mill. With the help of it in a short period of time, the holes are made of the necessary locks and loops. If there is a large set of cutters, then even better. If you need to make a door frame with special quality, a woodworking machine will be needed.
Some features
Door box device.
The process itself looks like this. Initially, a smooth board with a thickness of 5 cm (maybe several), 4 identical segments make it from it. 2 of them are equal to length, 2, respectively, the width of the opening.
At the same time, segments have only 3-sides processing - make them needed very smooth, 4th placed near the wall. Focusing on the width of the board, make a cut in which the door will be inserted.
The incision is made only on the side where it opens. If a double door is planned, cuts are made from all sides. It is easier to make cuts on a machine where it is possible to lift the table and adjust the required length. The existing material is cut to the required length, all ends are processed.
When all the necessary blanks prepared, proceed to the processing of transverse segments. The longitudinal compartments of standard doors have 193 cm, transverse - 90 cm. The cut on the end of the door box should be 1.5 cm, width - 5 cm.
Installing Doors: Recommendations
First, it is necessary to attach all the strappings that are top and side, and only then begin to install the box itself in the doorway. At the same time, there must be a space between the door and the wall in 2 cm. In the future, it is used thermal insulation.
Article on the topic: Dog's booth with your own hands: Two photo reports + video
One of the important elements in fixing the door is replaced. There are 2 options for feeding boxes: 45 ° and 90 °.
The diagram was drinking the door frame.
Put the box at 45 ° occurs as follows:
- Boards are taken;
- The necessary marks from the inside are set, unnecessary is removed;
- The dumping angle inside must correspond to 135 °, and outside 45 °, the length of the vertical boxes must be standard and the same.
Similarly, it is done with horizontal small bars. It is only distinguished by the fact that it is necessary to cut off from all sides. The most important thing is not mistaken in size.
To assemble a box of 90 °, placed ready-made parts of the future door on a flat surface. The corners are neatly connected using self-tapping screws, twisting 2 self-pressing in all angles (at right angles).
To keep the door frame in the desired position, it is possible to use several methods:
- Strengthen the door frame with small regions. Reiki must be secured by perpendicular to the racks of small cloves (screws).
- Adding wide and solid parts that are designed for fastening. Install all corners, carefully checking perpendicularity and verticality.
In the opening the doors insert the box and correctly installed in the center. At the end of all the work, it is necessary to check whether there are no cracks, distortions and other irregularities. If necessary, use the seal.
In order for the box to secure high-quality in those places where there is contact with the wall, put the seal.
At the end of all additional operations check the perpendicularity of elements on the side.
Of course, if you use all specialized tools and assistants who can submit details if necessary, make the door independently easy. Therefore, choose the option that is acceptable to you. Good luck!