[Create at home] How to make a stylish lamp with your own hands?

Things for home made by their own hands are attached not only to comfort, but also a special atmosphere. The lamp will bear the light in the family not only in the literal sense, but also in the portable - in the evenings will fill the soul with warm and joy. So, for lovers, a description of a stylish lamp will be presented with her own hands.

What is needed

To do this, we will need: pipe 2m30, switch, socket, wires, LED lamp with a thin profile (driver comes in a set), glue gun, two sewer plugs (one by 160 mm (it will be a ceiling, it will be molded), and the second - 200mm, they need to sand to sand, so that there are no molding lights), paint (we will paint in white gloss, and the foot is in red), PVA glue for building mixtures, building gypsum (it will quickly dry and easy to use and light By itself).

Tip! The radius of the pipe is optimally taken 18mm, that is, such that there was a mild bend, not very thin and not very thick.

Stages of work

1. Bend the pipe at a distance of 20cm from the end to get the right bend without the chances of 90 degrees, it will be a bar.
2. Drill holes in the pipe and insert 6 screws opposite each other in 3 rows with a distance of about 2 cm so that they stick to the caps parallel to each other.

Interesting! It is necessary so that there is more square of contact and the rod did not fall.

1. Painting the pipe of red paint - first once, fix it in an improvised paint chamber . Leave to push. Take up the following item and only then cover the second layer.
2. Base. There is a lamp with a driver that is better to disconnect because it is nowhere to hide it, it is too massive. You need to cut the wire, lengthen it, it will go down the bar. And at the bottom you need to install our driver. That is, the tube will go down, the wire will be published from it, enter the driver's case. The housing is easy to understand, it must be pouring it with hot glue, install on the bottom, so there will be easy access from below. And now more:

Article on the topic: Visiting the actor Matthew McConaja: a real chic and the taste of the interior

- Select the driver with a hot gun,

- walk in the circle of our lamp with a hot pistol,

- we extend the wire,

- Measure 18mm from the bottom, put the point, drill the pipe volume,

- Cut part in which our 18mm hole hole (measure about 4cm) to insert a barbell with screws, then return this part to the place and on the reverse side to close with glue so that it is sealed,

- We collect the base: Skip the cable through the bar, the side with the nails lay it into the hole, which is now u-shaped, seal the nails with a pistol, to pour it with diluted plaster to our stripes,

- so that the glue does not look so ugly - then you just need to warm the hairdryer and will all expect everything,

- after about 3 hours, the plaster will freeze, it needs to be pulled out (if it is frozen, then you will have to cut the ground),

- The moment of truth is to check whether the lamp is burning, since we poured it with water. If everything happened hermetically, it will burn.

1. Clean the light bulb with a knife. Our casting take, if there were additional feeds, you need to then take it, so that it was easier to get the base.
2. So, fill the base, with our seams and a barbell with self-draws, plaster. I remove this pebble after a few hours or a couple of days.
3. If there are flaws, you can simply add a solution.
4. Cook wires insert the driver into the case.
5. We screw the legs to the bottom of the base with self-draws, preferably not moving.

Conclusion

Thus, it turns out a lamp, which perfectly fit into the interior with its originality. It can also be used to work at the computer, and for lighting the bedside, sofa area. Under this flooring, it is very comfortable to read books, even watch TV. Torsher creates a cozy atmosphere, which can even be called romantic.

Lamp made of pipes with your own hands (1 video)

Article on the topic: Russian video clogger Yuri Dor: Interior Review in the Moscow Apartment

Homemade lamp for home (5 photos)