The platbands can be called a decorative app to the door design rather, as they mainly hide the building shortcomings associated with the wall and the same door. That is why, before making a cash of the entrance door, there is no need to be especially prepared in technical terms. Although the sake of justice it is worth noting that the accuracy will still be needed, especially when the planks are sawing.
The ticket is necessary for the obstacle to dust and dirt in the door slit, as well as the increase in sound insulation properties.
But before drawing up the doors with their own hands, it would not hurt to deal with some technological nuances of this element.
Varieties of dext and its installation methods
On the construction market, tickets can be found from wood, MDF panels or plastic, in some cases can be found from aluminum or steel. If a bathroom is located near the entrance door, it is better to install platbands from veneered MDF or PVC, since these materials are tolerant to the effects of temperature and high humidity.
When using liquid surfaces, the surface should be perfectly smooth, otherwise the panels will not sit tightly and leave the gaps under them.
In order to attach a cash on the door with your own hands, it is best to use liquid nails. Although such a process can be done with thin nails. But if the choice is to stop in the second version, before starting work it is necessary to cut all the caps of nails. If it is not possible to carry it out on your own, you can use the construction gun, which is charged with such studs. In the case of applying all the same hat nails, it is necessary to take care of their disguise. This can be done with a special corrective pencil or acrylic sealant.
It should be known that to use liquid surfaces of the surface should be perfectly even, otherwise the panel will not sit tightly and leave the gaps under them.
Article on the topic: how to plaster corners properly
The navigation from the MDF is very similar in structure with wooden analogues, but it has its own way of fastening. Such planks are quite fragile, so the guide holes for nails are prepared by pre-middle diameters of 1-1.5 mm. Only aperture should not be through.
If it is decided to use plastic, it is better to glue it. The convenience of such a material is to be cheap. Therefore, if it didn't manage to cope with the first time with the first time, it can be safely removed and start again. Also, the plastic is flexible enough so that when it is installed, it was possible to allow working with uneven walls.
Scheme of figured ends of cash from MDF.
Working with aluminum panels must be harvested with self-tapping screws, only with their help, such platbands can be fixed on the design.
In this case, the form of platbands can be represented by flat, rounded or relief. The most frequent use are flat panels, but the latter are used if the room is decorated in an interesting design solution.
A ticket can be fixed with an invoice or telescopic (used for unevenly installed doors).
How to choose angle stored under the joint?
At this moment, the shaped relief is very affected with the front side. You can mount a navigate two materials: a flat bar without any gaps using a straight angle, or pick up the cap. At the same time use horizontal or vertical direction. Before starting the installation, all the sleeves must be painted or toned with varnish. Also, the angles should be smooth, that is, the saws treated from roughness.To install relief panels that have a rounded surface shape, a standard angle of 45 º is applied. In this case, it is necessary to accurately control the angle, otherwise there is a chance to get gaps.
Required tools
To install platbands on the door, you will need: roulette, level, coupler and other tools.
Article on the topic: Interior red doors in the interior
Need to prepare:
- Stuslo;
- hand hacksaw with small teeth;
- Mounting or screwdriver;
- roulette;
- Building angle;
- tracker;
- assembly tape;
- nippers;
- Nails without hats or special construction gun.
If there is an opportunity, it is better to still use a tracing machine with a turning platform, in which case you can achieve ideal angles.
The first stage goes, of course, dismantling the old platbands. At this moment, you must remove all old nails. This process uses a mount or screwdriver. Attention should also be paid to the hard bar, since in some cases it also has to be replaced. If such a need arose, then it should be paid to its fixation.
The best option is the factory production of this element, as there are all the conditions in order to make a product with high quality, most importantly, with perfectly smooth edges. To make a good match, before purchasing it, you need to measure all the protrusions and irregularities of the wall.
Workflow: Recommendations
Initially, there is a check of even the walls of the walls, especially in the place where installation is planned. It is very important that they are located in the same plane, otherwise it will be nailed, gaps and gaps are formed.
With the help of a construction corner on the reverse side of the panels there is a markup.
Diagram of installation of door platbands.
Cutting parts of the required length is performed with a hacksaw or special apparatus, if any. For the suspension to the resulting measurements, it is best to add 5 mm, so there is a stock in case of damage to the material. Fitting marks a cut line. Special role will not play, with which part of the tickets to start producing the mount.
As mentioned, it is necessary to prepare nails. Therefore, you need to worry about in advance and save them from the hats with the help of a bustard. Thus, a neat aesthetic look of the entire product is achieved. Nails are driven into the surface in increments of 0.5 m.
For top of the tickets, short parts are most often used. One of the corners washed under 45 º. Next, the resulting segment is trying to place and mark the top of the angle from the other edge, after which it is fixed.
Article on the topic: The plastic balcony door does not close: how to troubleshoot
It happens that the slots are formed on the place of the joints, which can be eliminated using a special sealant, which can be chosen in the tone of the tickets. They are formed in the case when the sawing angle is disturbed. Before it uses, in order to protect the design from contamination, the parties around the gap are stuck in the assembly tape, and after drying the sealant, it is removed. To attach the platbands from the opposite side to act in the same way.
Print must match the material and color of the door.
All installation work must be carried out after work with the walls is over (for example, after sticking wallpaper), but before starting to lay the plinths. Repair work specialists are recommended when installing cash, retreat from the wrong side of the door design by 5 mm and at such a distance to install.
Mostly experts recommend starting work from the location of the door loops. It should be noted that the platbands at the entrance door are attached only from the inside, as often external already go ready as a component of the door frame.
Functions and features of cash
Prints give the finished image of the entire door design. But besides aesthetic destination, they have a number of other functions that are also fairly useful:
- prevent the ingress of small particles of dust and dirt into the residential premises;
- increase the noise insulating properties of the entire door design;
- Hid to hide the flaws of construction work with the edges of the wall and door structures.
In general, if you summarize, the installation of cash on the entrance door does not require too much effort or any specific skills, and you can even do without highly specialized tools. The main thing is that it is required is the accuracy and scrupulousness of the calculation and sawing in the panels.