Everyone engaged in the construction of a brick house, thoroughly think about the walls of the walls in the finished building. In any case, the interior decoration of the brick house depends on many factors. For example, inside the house there may be drops of temperature or humidity levels, which somehow affect the state of surfaces.
What can be separated brick walls
In most cases, the inner finish of the brick house is much more complicated than the external, which is carried out using the installation of siding panels, plaster or ordinary painting. If the finish is required to the house in which you are only in the summer, for example, we are talking about a country summer cottage, then in no case use drywall, since this material is very poorly tolerated the impact of moisture and temperature changes. You should not hinder the walls with wallpaper, since such a finish can last not long without heating. In such a situation, it is best to use the "wet stucco" method.Among other things, do not forget that in the case when the brick house is insulated, it is necessary to create a vapor barrier layer, which will save the insulation from excessive absorption of moisture from the air, because it can lead to the loss of thermal insulation properties and makes the entire process of insulation completely meaningless.
The internal type of finishing at home is divided into two main stages - rough and clean. On the draft stage, the installation of engineering communications occurs, as well as the warming mentioned earlier. If this is provided for by the project, additional sound insulation can be made. The finishing assumes all the necessary works from top to bottom: first the ceiling, then the walls, and at the end - the floor. This approach allows you to get rid of many possible problems.
Article on the topic: Make a cellar of reinforced concrete rings
If wooden floors are installed in the room, then they are best to separate them with the help of lining, and if the beams are made of reinforced concrete, then it is necessary to need putty and shuttering . The ceiling design finishes must be coordinated with wall decoration to obtain a harmonious composition in the interior. The same conditions and flooring, which must also correspond to the overall concept of house or apartment inside.
Preparation of walls to finishing
The classic option used in order to solve a brick house with high quality is plaster. This material used inside the building carries several positive aspects immediately. First, a decorative moment, since the plaster can be used not only as the basis for any type of finishing, but also is an independent material that allows you to create excellent decorative solutions. Secondly, this material is used to align the walls, which is very relevant, since the brick house is often quite problematic surfaces, it is simply impossible to work with without prior alignment. Another function that the finish is tired with the help of plaster is thermal insulation, but for its implementation it is necessary to use a special "warm" variation of the material.
The internal type of finishing made with drywall will be perfectly. The preparatory process before the start of such surface treatment is quite simple. The wall is equipped with a special fraud frame or aluminum, which provides the necessary air layer, which allows you to maintain heat in the room. It is on this frame and the plasterboard panels are attached. In the event that the wall is smooth, the panels can be fixed directly on it using a special adhesive solution or mastic.
Important moment - Soundproofing
If you decide to provide good sound insulation in your home, be prepared to spend time and means. The most widespread solution to this problem is plastering surfaces. To do this, the brick house from the inside is equipped with a reinforcing grid, to which the plaster mortar will be applied. Thus, the walls are not only isolated from extraneous noises, but also align.
Article on the topic: How to close the gap between the floor and the wall under the plinth
Naturally, for obtaining the highest quality results, I recommend using a special material - a sound absorber. In order to separate the brick house with it, you need to build a wooden frame, the racks of which will be on distance from each other at more than fifty centimeters.
I advise you to leave a small gap between the bars and the wall, the width of which should be enough to lay a soundproof material, the laying of which should be made with residual intake on the floor and the ceiling.
On top of the frame, the above-mentioned decoration made of drywall is carried out, which allows you to create an additional barrier that enhances the properties of the sound insulation material.
Video "How to separate a brick house inside"
On the record of an interesting selection of photos of the design of the inner part of the brick house.