For a prosestrant (otherwise a prosest flooring or tail overlapping), it is customary to call a special flooring of the floor, which is made from the flooring of the boards and is fed as a rough coating over the beam overlaps.
Where applies
This is the simplest wood coating, which, as a rule, is used in pure form only during the construction of non-residential premises. Such a limitation is explained by low thermal insulating and noise absorbing properties that have similar floors.
Typically, such a coating is used in garden houses or buildings of an attic reason, where the high level of thermal insulation is not required, since the buildings are operated mainly in the summer. At the same time, the flooring becomes ceiling overlap below, and the upper flooring serves as a floor for the attic.
Tip: If plastering trim of the ceiling of the lower floor is planned, then the board does not take the board for the bottom floor, and at the same time leave the gaps between the boards. To subsequently, the plaster in the seams did not forcerate, and it did not go cracks, the length of the boards should be made jerseas and score wooden wedges in them. Such a stuffing ceiling must be plastering along dunke.
The meaning of the device of the privileged floor is to store over the beams of the boards, which will serve as a hollow for the attic.
If there is a goal of isolate the room from the attic to increase sound insulation and keep heat, then make the binder. In it, the prostinal layer is stacked among other layers in the following order:
- flooring from boards, better tipped;
- Overlapping beams;
- noise absorbing material;
- The floor is the Promstable.
The scheme of the staircase is shown in the figure, where 1 sheets of plasterboard; 2 - overlapping from a t-shirt; 3 - waterproofing layer; 4 - sound insulation layer; 5 - beams; 6 - lags; 7 - Black floor; 8 - Bar.
Article on the topic: Device fence from a tree on a balcony and a terrace
What makes the prosest floors?
The prosestful flooring are a variety of rough floors. Unlike a set type of roughing, this species can be a simple jacket flooring, bars, they are placed on top of the beams. If a timber is used when the device is used, then it is stitching.
If the boards are used, the so-called blackboard is usually used. The boards have grooves and mounted braziness, which is very convenient and practical, because it turns out even, without a slot surface.
The following scheme shows the location of the layers in the device of such a floor using the tape:
The overlapping scheme using a device into a roll, where in Figure A is a coating using the insulation interlayer (bottom-ups go beams, then the bars then forgave the draft coating, two layers of pergamine, between which the insulation is laid, the finish board goes).
In the picture B - with a row on cranial bars with sound insulation: the first two layers are the same as in the first version, then the ceiling cover, the rolling, soundproofing and parchment, and completes the entire finish board.
Figure B - Scheme with rolled on beams without bars: where the beams go from below-up, then the boardwalk, layers of pergamine and insulation, rough floor and finish with sex.
Use in the floor
In addition to its initial task, such an intermediate flooring plays an important role in creating a high-quality semi-layer coating. From how reliably this layer is laid, the service life of the entire floor in the house depends.
As is known, in the floor of any type of dwelling - something like a cake consisting of different "fillers." And if the strength of the concrete base depends to a greater extent from the smoke of the screed and the quality of the finishing coating, then with wooden floors achieve quality much more difficult.
Article on the topic: Bedroom design 12 square meters. M: how to equip a small room + ready-made planning (36 photos)
Wooden floors are a traditional base in houses used by Izstari. Over time, it began to be crowned with new, by no means the best materials.
Artificial materials come to replace wooden structures not so much due to the fact that they are much more attractive as due to the fact that they are easier to mount and care. As for the tree, the peculiarity of its laying makes this type of sex more complicated in the installation.
But if you decide to make a classic wooden floor in your apartment or house, you get it for many years eco-friendly, reliable and beautiful. At the same time, not obsolete, but modern and stylish.
Laying of prostaste floors
Directly styling of the prostinal floors is as follows:
- Prepare the bottom base of the floor - to dry, predict;
- lay a moisture insulation layer in the form of a polyethylene film;
- Install lags across the long side of the room;
- Prepared and sawed on the size of the board to nail to lags with nails.
This is an easy way to make a draft coating. It will become the middle layer between the soil (or overlapping between the floors) and the finishing gender. It will divide the cold zone between the ground and the final coating. When laying insulation and soundproofing layers, as shown in the picture above, the house acquires better protected from cold and noise.