After the log is put, it is necessary to wait for shrinkage, until this point it is impossible to carry out the inner finish. Prior to that, planning and calculation of finishing materials is performed. The bath from the inside can be finished with a limited amount of materials offered. For the washing department, the pre-banker, the steam room applies products that moisture and sharp changes in temperature are not terrible. It is best to use natural wooden lining for a steam room and a ceramic tile for a bathroom. For a relaxation room, an entrance hall can be taken by other materials, but choose such moisture is not terrible.
Firing a log cabin retains the environmental friendliness and naturalness of the building.
Wooden lining
The pair is usually triggered by lining. The log house in this case is turned off attractive, while the design of the walls and the ceiling looks stylish. There are various options for lining, but you need to take those that are resistant to moisture. The chalk thickness should be up to 220 mm, the laying can be produced in a vertical or horizontal position. The choice depends on the height of the bath ceiling. If it is up to 2.5 m, then you can use vertical laying. If the ceiling is high, then the horizontal method is suitable, since the standard length of one board is no more than 2.5 m.
Types of lining.
The best option will be fastener for a wooden rail crate. It stacked with a 50 cm step. Under the walls, the walls are carried out by the necessary communications, they must be protected by a special corrugation. The easiest way to fasten the board - groove-cream, additionally each board to the crate is nailed with thin galvanized nails. The decoration of the shrue of the bath from the far corner of the room begins, while working is recommended to use the construction level so that all rows of the boards are smooth.
Using plastic
Plastic lining is suitable as inexpensive and fast finish. Such a method is used infrequently, the log house is usually shaken. Plastic lining will be appropriate in the rest room. The horizontal or vertical laying method is suitable. The connection of individual panels among themselves should not be dense. Starting work on the design of the inner walls of the church should be with the installation of the crate. For this, thin wooden rails are applied, they neatly nourished against the wall in a step of 30-60 cm. The mount is made galvanized nails, the planks themselves are desirable to handle the antiseptic before work.
Article on the topic: How now fashionably glue wallpaper: Popular directions (photo)
Disadvantages of fastening lining with nails.
After the crate, molding is mounted, it is attached from the floor and the ceiling. It is in this molding that the end parts of the start panels will begin. Fasteners begins from the leftmost wall, the panel lattices are fixed with nails or glue, they are connected to a spike groove method.
Interior decoration is performed as quickly as possible, its advantages in the following:
- Communications can be easily hidden directly behind plastic panels.
- The cost of work is low, the surface is practical, it is easy to care for it.
- Works do not require special experience, are performed in the shortest possible time.
- The color range of panels is used in the most diverse, which allows you to make the room more attractive.
There are cons:
- Plastic is not the most attractive material from aesthetic point of view. You can hide under it a log log in it only if it is not very attractive in itself, has defects.
- Plastic is easily flammable, with too high temperatures can melt. Therefore, it is possible to use it only for a rest room, but not for the steam room.
- The surface is unstable to mechanical damage.
Use of unique materials
Installation of lining.
The inner lining of the cut can be not only standard, but also exclusive. For the floor it is recommended to use a massive or parquet board, for the ceiling applied a regular board, for walls - wooden lining. Such a decoration of the cut will be stylish, cozy, environmentally friendly.
If the fastening "in the bowl" was used, the inner surface is simply cleaned from the bitch, the wooden fringe grinding machine. After that, the surface of the tree is covered with a special protective varnish. The electrical wiring is placed in the corners of the room, on the floor (closed by the plinth). All pipes and other communications are laid under the floor. In the rest room, the walls can not only be varnished, but also cover with a thin layer of paint, using natural shades, such as chestnut, white, cream. Before the painting wall, it is best to spit to remove chips, cracks, bitch on the surface of the logs.
Article on the topic: Stains on the wallpaper fired after sticking: how to remove and output
Advantages of interior decoration:
Tools required for mounting lining.
- The costs of decoration will be minimal;
- The appearance of the bar is natural;
- Work is extremely simple, do not occupy a lot of time.
There are also disadvantages of varnishing or staining:
- The surface will not work perfectly smooth;
- The design is unay, there is no special choice;
- Communications are not so simple, there is a need for their protection against humidity, temperature drops;
- Every 4 years it is necessary to update the walls of the walls.
Jute rope for decoration
One of the options for designing the inner walls of the bath is the use of a conventional rope or jute. This method of finishing with jute is acceptable for buildings built according to the technology "in the bowl". For log cabins set on another method, it is better to choose an alternative way of finishing work.
The work begins after the inner surfaces of the premises are completely processed by the antiseptic, their grinding is performed. It is recommended to purchase a special decorative rope for work, its cost is not so great. It is stacked only in the crowns, performing two roles at once - protective and decorative. The rope can provide insulation, protection against moisture penetration, wind.
The floor is placed wooden, it is best to apply a massive board, which after laying is impregnated with special oil or varnished. For the ceiling, it is recommended to take a wooden lining, the most protected from moisture. It is best to start working on the finish when the log house is mounted, and the logs are a little sharew. It happens in about a year after the structure is fully prepared. The rope is attached differently in the crown in different ways, special nails are most often used, which have plastic hats. You can use brackets and glue. Before laying the rope should be carefully treated with antiseptic.
Before laying the rope is measured at the required length, after which it is cut off. It is necessary to ensure that the edges do not disengage him. To do this, they first wrapped with threads, after which they are covered with a layer of varnish or glue. In the starting point of fasteners, glue is necessarily used, which makes fixation as reliable as possible. It is best to do this from the bottom angle, missing the plot with a thin adhesive layer. The glue composition of the thermopystole is applied, it is impossible to use ordinary glue.
Staples and nails can be used as an additional fixation, this method will be the best and reliable.
The rope is placed on the adhesive layer, after which every 15-20 cm it is fixed with nails. When the design of all the crowns and the joints of the shrue of the bath, it is necessary to cover the wall of the cut and the rope with a layer of protective varnish.
Article on the topic: An attic stairs in the interior (48 photos)
The inner finish of the shrue bath is not as difficult as it may seem. In many cases, the simplest materials are used, only the surface varnish can be performed. This is due to the fact that the natural log, from which the walls are manufactured, attractively in itself, it does not need a mandatory finish. For work, you can use various materials, but it is not necessary to remember that not everyone is suitable for the bath, but only resistant to high humidity, indoor temperature drops.