Box for linen with your own hands
Such a box for linen is so convenient that it is capable of calling the members of your family a desire to not scatter dirty clothes all over the house, but to fold in this box.
There are two compartments for "light" and "dark" linen in the box, and there is nothing easier than manipulating it with a self-closing door.
The dirty linen used in this project actually represent two standard plastic garbage containers. You can find these durable containers in almost any store selling kitchenware, or in a construction supermarket. If you prefer a linen box with one container or if your containers differ in size, you can adjust the necessary dimensions of your lingerie. The design of the box and its design will remain the same.
Box for linen with your own hands
Choosing wood, chipboard or plywood will be determined by what kind of finish you will prefer. If you are going to paint the box, an economical option for details from solid wood will be pine or poplar. The top panel of the box is easiest to make out of the sale of glued panels, however, if you fail to find the desired material, it is easy to make a glued panel for a box with your hands from the board with a nominal thickness of 2.5 cm. You can also use for a linen box chipboard, Which is widely available in furniture stores. The complexity of the making drawer manufacturing makeup is relatively high.
List of materials for making linen box with your own hands:
- Side walls (plywood) - 1.9 x 29.8 x 75.3 cm - 2 pcs.
- Rear wall (perforated super hard-hard DVP) - 0.6 x 75.3 x 87.0 cm - 2 pcs.
- Leading on the front edges (solid wood, chipboard) - 1.9 x 1.9 x 75.3 cm - 2 pcs.
- Scrolls (solid wood, chipboard) - 1.9 × 7.0x85.1 cm - 2 pcs.
- Upper corner struts (solid wood, chipboard) - 1.9 x 8.9 x 8.9 cm - 2 pcs.
- Limiters (solid wood, chipboard) - 1.9 × 3.8 × 3.8 cm - 2 pcs.
- Lower corner blocks (solid wood, chipboard) - 3.2 x 3.2 x 7.0 cm - 4 pcs.
- Tilt limiters - 1.9 x 3.2 x 3.2 cm - 2 pcs.
- Door with platform
- Door (plywood) - 1.9 x 64.1 x 80.9 cm - 1 pc.
- Side covers (solid wood, chipboard) - 1.9 x 1.9 x 64.1 cm - 2 pcs.
- Top pad (solid wood, chipboard) - 1.9 x 1.9 x 84.8 cm - 1 pc.
- Platform (plywood) - 1.9 x 27.9 x 84.8 cm - 1 pc.
- Truck (plywood) - 1.9 × 26.0x26.0 cm - 2 pcs.
- Top panel (solid wood, chipboard) - 1.9 x 33.7 x 92.7 cm - 1 pc.
Article on the topic: Wall-mounted shelves: 28 Ideas for storage
Armature and fittings for linen
- 38 mm Finish nails.
- Shules with countersunk heads No. 6 38 mm.
- 22 mm Finishing nails.
- Shurutes with secret heads No. 6 32 mm.
- Wooden tubes with a diameter of 10 mm - 20 pcs.
- Shuronds with secret heads No. 6 41 mm.
- Self-adhesive rubber or plastic lining with a diameter of 19 mm - 4 pcs.
- Door handle - 1 pc.
- Bivaluble end loops 63.5 mm - 2 pcs.
- Garbage containers - 2 pcs.
General view of a box for linen with your own hands. Production of a box of linen box.
1. Production of details with your own hands. Cut out the side walls of plywood, the rear wall of the perforated superhard DVP, and the remaining parts of the case - from solid wood or order the cutting of the chipboard in accordance with the dimensions specified in the list of materials for the manufacture of the laundry box with their own hands. Choose seams in the side walls for fastening the back wall, as shown in the figure "General view of a drawer for linen with their own hands." Haves with a chief cut down rounded openings at the bases of the side walls.
2. Fastening overlays. Apply glue to the opposite sides of all overlays. Attach the lining to the front edges of the side walls of 38 mm nails.
3. Drilling holes for screws. Zenkovka or drills with a diameter of 9.5 and 4.8 mm. Slide and drill in crossings of the hole for screws, as shown in the figure "General view of a drawer for clothes with your own hands."
4. Fastening the across and rear wall. Wholes and screws attach the bottom corner limiters on both ends of the lower side of the laundry box so that they are flush with its ends. Use screws number 6 38 mm. Then attach the top and bottom crossbar to the side walls of the linen box, using glue and 38 mm screws, as shown in the figure "General view of a lingerie box with their own hands." Next, apply glue to both fold of the rear edges of the side walls and put the back wall from the Fiberboard. Attach it with 22 mm finishing nails, driven into the fold.
Article on the topic: Causes of the weak head of hot water from the gas column and what to do?
Countersink. In the manufacture of furniture, with your own hands, use the cenks. As a rule, there is a sufficient set of mirrors with a size of No. 4 to No. 12. Although you can drill and sprinkle the holes with ordinary drills, it is more convenient to make it more convenient to the cenks. This is a minorizing tool on wood. Zenkovki used to obtain conical or cylindrical deepends, removal of the champs of the center holes, producing the support planes around the holes.
5. Fastening the upper corner spacers. Make your hands the upper corner struts in the form of triangles. Set them into place on glue and screws, as shown in the figure "General view of a linen box with your own hands." Use two 32 mm screws to each strut.
6. Hiding holes from screws. Close the splashed holes with wooden plugs, lubricated glue, and polish flush.
7. Production of the top panel of the laundry box with your own hands. Bring three boards to a width of 14.0 cm and cut them up to a length of about 96.5 cm. Apply glue on the edges and squeeze them together with three whims or pipe clips. When the glue is freezing, squabble all the excessive excess and bring the panel to the desired size according to the materials in the list for the manufacture of a box for linen. Round the edge of the milling machine panel with the corresponding cutter. Process only lower edges.
8. Setting the upper panel of the box for linen. Drill with a diameter of 4.8 mm Drill two holes in the upper crossbar and one in each rear upper corner strut, as shown in the figure "General view of the laundry drawer with their own hands." Since the upper panel is made of solid wood, it will expand and shrink when air humidity changes, so it needs to provide some freedom of movement. To do this, when drilling holes in the upper crossbar, slightly negotiate the drill parallel to the ends of the cross. The resulting elongated hole will give the necessary freedom of movement. Position the top panel of the box for linen so that it is flush with the rear wall and performed in front and on the sides of 1.9 cm. Attach the top panel to the crossbar and the angular struts 32 mm screws with countersunk heads.
Article on the topic: What affects the heating rate of the water heater?
Manufacturing and installation of the door and platform
1. Production of details. Cut the door, platform and triangular plywood plywood with a thickness of 1.9 cm in accordance with the dimensions specified in the list of materials for the manufacture of the laundry box with their own hands. Cut three overlaid on the edges from solid wood.
2. Production of the door with their own hands. Attach the pads on the upper and side edges of the doors on the adhesive and 38 mm finish nails. Create the door with a platform to four 41 mm screws, having previously sprinkled by holes as shown in the figure "General view of a drawer for linen with your own hands." Close the holes with lubricated glue with wooden corks and passing the tubes flush with the surface.
Determination of the location of the liner tilt limiters
3. Fastening the door handle. In the middle of the doors at a distance of 38 mm from the top edge, drill an auxiliary hole and attach the door handle with an accompanying screw.
4. Setting the lower corner blocks. Shift rubber or plastic linings on the lower edges of the blocks. Fasten the blocks with glue and screws, pressing them to the side walls of the drawer and the bottom crossbar, as shown in the figure "General view of a drawer for lingerie with your own hands." Take care so that the gaskets are located at a distance of 1.9 cm from the front edges of the side walls. Use screws No. 6 32 mm with countersunk heads.
5. Door hanging. Position the loops at a distance of 5 cm from the bottom corners of the door. Select the sockets and hinges on the door. Then insert the door to the opening of the box and place the place for the second hinge flaps.
6. Installation of inclination limiters. Make tilt limiters in accordance with the dimensions specified in the list of materials for the manufacture of the linen box with your own hands. Measure the width of garbage containers. Wrap the door so that it is convenient to put containers and extract them from the box. Make a pencil mark in the place where you would like to locate one of the limiters. Attach one limiter to the marked place with glue and one 32 mm screw. Wrap the door forward and install the second limiter.