Beading is a very interesting and creative occupation. We are very easy to weave the beads, it is enough just to show a little effort and fantasy. Bead bracelets are a very beautiful and original product that even newcomer can do. The schemes of bead bracelets for beginners are very easy to use.
Tangled "Cross"
This type of weaving is very popular and known. A lot of schemes are built on its basis.
First you need to take a long wire or fishing line, put 4 beerins on it. As shown in the diagram, to turn the bottom of the fishing line through the last beerink so that the ends of the fishing line are crossed.
On one side to wear one biserech, and on the other - two. Throw a fishing line, where one bisper, through the last on the other side. Then, on the contrary. Wear two beads on the side where there was one in the previous step. And one where there were two before. Continue weaving to the desired length and repeat the 2 previous steps. As a fastener, you can use the usual small button.
Light "pigtail"
Many lightweight bracelets walked through the technique of "pigtail".
Those who have never been engaged in beads, it is worth starting with this technique.
At the beginning you need to take three segments of a durable color thread, fold them together. Secure down the node so that the bracelet can be fastened. Start weave the braid from the threads and take turns to ride beads for the last threads. It is necessary to monitor the beads to be smoothly. Tighten and correct.
Weave to the desired length, at the end to bind the button that will become a fastener. You can not immediately start torsion beads, leave an empty pigtail on the edges of the bracelet. Optionally, you can use the threads of other colors, use beads of different sizes, colors and shapes. The result can be seen in the photo:
Multi-line bracelet
To begin with, the wrist girth should be measured slightly above the brush. To the resulting number, add from 7 to 25 mm, depends on the required length of the bracelet. From the resulting number, it is necessary to take the length of the fasteners of the product and two connecting rings. At the end of the calculations, the length of the finished bead threads will be.
Article on the topic: Master class on Autumn Topiari with its own hands from natural material
Next you need to cut off the thread of several centimeters longer than the bead thread. Insert it in the needle and at the end to tie a couple of nodules. To the tip drops a couple of drops of glue and nodule threads put in glue. And after carefully pliers on the node press the tip. Now it's time to start the biserinium rolling.
During the bayer rolling, you should not forget that you need to stop the work at the moment when the length of the thread recruit will reach the required mark.
After all the beerts turned out to be striking, it is necessary to tie a nodule. Very close to the last bead should not be tied, otherwise the thread will be excessive pressure, and it breaks. Try to bend the stripped thread if it bends easily, it means everything is done correctly. On top of the first nodule tie a couple more nodes. The end of the thread is also to cry and climb the same way as with another end. Extra threads from the tips to cut.
After completing the work, decompose everything is strained in such a way that I like more. You can cross each other all strands so that the bracelet becomes a bit "confused".
At the end you need to reveal the connecting ring. Place all beading threads from one end of the bracelet. For reliable closure, the ring can use pliers. From the other end of the bracelet, consolidate the second connecting ring with the threads rolled on it. Remove fasteners on the fastener and strengthen it to the connecting ring, set the pliers. Multi-line bracelet from beads ready!
Bracelet "Lace"
Weaving beaded lace bracelet will increase the experience and skill of any craftswoman. This is a very wide wicker strip, decorated with a complex ornament in the form of flowers-crosses and multicolored stripes.
First, put 11 beads on the working thread or fishing line. Take 9 pink bispers and 2 - red. Through the hole in 5 beads to spend the needle and tighten the loop. Then dial on the needle 3 purple beads and through the first bisper to skip the fishing line. To form the second link bracelet to the working thread, 4 beads: 3 red and 1 purple.
Article on the topic: Cross embroidery scheme: "Owl" free download
Next skip the needle through the middle bead in the top row. Now you need to put on a thread 2 of red beads and 1 purple and turn to the hole to the tenth bead. And after you need to perform all actions by a similar scheme and change the selected colors of beads.