Drinking the jigsaw may be required when finishing works, but most often in the process of manufacturing furniture with their own hands, shelves and other things. Drinking itself is not so complicated, but to make this work efficiently, it is necessary to immediately prepare all the materials and tools, strictly follow the uncomplicated rules and recommendations.
Crafts from plywood serve not only element of the decor, but also used in the household.
It concerns this drawing transfer to plywood harvesting, drinking simple and complex artistic elements. It is also important to keep the jigsaw right and correctly during operation, to ensure all security measures, as when working with any other tool.
Tools and materials
Lobzik drinking requires not only experience, but also the use of a certain set of materials and tools. These include:
When drinking products from plywood with an electric bison, it is necessary to accurately perform work so that it does not work out an uneven line of cut.
- Plywood sheet. It is necessary to choose the material that most complies with the requirements of the work. Usually a thin sheet is used, consisting of multi-layer wood hardwood. Depending on the complexity of the work, the usual or moisture-resistant plywood of any suitable variety can be used.
- An ordinary manual junk can be used for drinking, if the works are not very large, consist in drinking thin artistic parts. But it is possible to apply an electric tool that is suitable for a large amount of work.
- Silo is used to make holes for propilov. At the points neatly pierced a hole with a diameter sufficient so that you can insert a drink. After that, the pumping process begins. Instead of sewing, you can use a drill with the drill of the required diameter, so it will be much faster to prepare holes. The selection of this or that option depends on the convenience of work.
- Dumping the jigsaw does not cost without buying a set of files. They are needed in order to correctly clean all the edges of the propyl. It often happens that in a very experienced master of the edge, it turns out a little ribbon. In this case, a file is selected, which more than others corresponds to the material, all the edges and ends are neatly cleaned.
- The resistant plate is used to strengthen the material and tools. It is important for working with thin and small parts that the working surface keeps smoothly, not loosened.
- There are other tools that may be required. It is usually a joiner's hammer, pliers, a sharp knife with replaceable blades, a circulation and a pencil, which will be required to apply a stencil on the surface.
Article on the topic: Creek in the country area. How to equip and arrange with your own hands?
Usually, in the presence of experience, the wizard immediately apply drawings to the surface. But for beginners will need special adhesive paper, cottka. In this case, it turns out to make a drawing on the plywood as accurate and beautiful as possible, and the lines will be smooth.
When choosing a tool, attention should be paid to ensure that it matches the work being performed. For example, for small parts, it is best to apply a hand tool that is most convenient, but with large volumes, for example, when assembling furniture, shelves and other things, it is already necessary to use electric jigsaw. Art cutting is rarely applied, direct feeders are mainly performed, cutting large parts.
How to use the jigsaw for art cutting?
When transferring the drawing to the plywood, it is sufficient to make the pattern to the plywood sheet and move it with a pencil.
For artistic cutting on the plywood, special techniques and methods for working with the jigsaw must know, they will allow much to relieve work. In addition, to use the tool is needed correctly and gently to avoid injury.
It is necessary to start work only with good lighting, all tools and materials need to be prepared in advance. Drinking by the jigger of artistic parts is distinguished by some features, it is impossible to rush, work should be done carefully and clearly. If you do not comply with the prescribed recommendations, it will be uneven, cuts will be "torn".
Recommendations for work with the jigsaw:
Proper hand set when drinking a jigsaw.
- The power tools must be kept strictly vertically, driving up-down movements during operation, in no case can not rock the pylon, tilt it. If you do not comply with this condition, the feet will be stuck in the tree, and the cut itself will be oblique. Another problem is the pink break, and this can already lead to injuries.
- When internal contours are cut from plywood, it is necessary to first make the hole with a drill or seer. After that, the feeder is inserted into the cooked hole, the saw process begins. It is important that the teeth were in the right position, the turn need to be done without interrupting the cutting process.
- It is necessary to ensure that the pink is stretched smoothly, is well fixed, otherwise injuries are possible. This is a prerequisite for working with any tool. Yes, and the work itself will become uncomfortable and poor quality.
- During cutting, it is impossible to allow the pink to vibrate, as the plywood sheet will begin to split, rush. The edges will not be so smooth, the work will have to begin again. If the jigscription is used for fine plywood, then it is necessary to additionally take a bar for fixing the working surface on the workbench.
- As you cut, you need to move the Fanoire to meet the jigsaw, but it is impossible too hurry. Lobzik himself should move in a vertical position, it is impossible to tilt it.
Article on the topic: Metric for Girl Embroidery Cross Schemes: For Boy Children's, free download, Sets without registration
Dumping a jigsaw of simple figures
Simple paddling patterns.
Cutting from plywood of simple figures is quite simple, it is only necessary to clearly stick to the lines. Smooth lines, arcuate, direct are done in this way: the peeling teeth should be directed strictly along the line, the logsik does not unfold - this is the main condition of the neat cut.
If you do not comply with this rule, the pilking will simply "get boggle" in the tree, it will turn it out, and the work will continue to be impossible. It is impossible to have a strong pressure on the material, the feck should go smoothly, the hurry should not . Lobzik himself returns to the vertical position, the canvas is aligned independently.
Sharp and stupid corners need to learn to drink slowly. For blunt angles, the reception is used in place, i.e., the cut is performed smoothly, after which the plywood unfolds. As a result, it turns out even and beautiful cuts with the necessary degrees of reversal.
Figure templates for sawing by an electroll bison.
If there is a need to drink a detail with sharp corners, then you can use the method of loop formation. At first, one side of the angle is formed, then a cape neatly on the outer contour so that it is possible to form the second side of the outer acute angle of the required size to immediately form the second side of the outer acute angle of the desired size.
All these methods are used to cut different parts, and how to make internal propellers? To cut stupid and sharp corners (for example, stars, leaves, flowers, geometric ornaments), it is necessary to carry out such a set of actions:
- At first, a seer or a drill with a thin drill is performed with a hole from which the plywood will begin to the top of the future angle.
- After that, the web is returned to the initial position on the cut.
- Now you can start forming the second side of the angle, moving in the desired direction.
How to transfer the drawing to the plywood sheet?
The direction of the teeth of the pink.
Article on the topic: Wallpaper mustard colors in the interior of the room
So that the patterns are smooth and beautiful, it is necessary to carry the drawing on the fane neatly. As a rule, without a pre-trained sketch, it is not necessary, it is obligatory to fulfill work.
The easiest option when the artwork is carried out, the use of tracing is considered. The drawing is transferred to the workpiece, after which it is cut. The price of such a tank is low, it can be bought with a reserve. But the process itself requires care and patience - every line will have to be transferred manually by observing evenness and accuracy.
You can use and not such a time-consuming method of applying the drawing to the plywood sheet. For this, the projector is used, which only projects the desired image to the working surface. But there are here and their nuances. The projector must be available, and its cost is not the lowest. Phaneur cannot be shifted, it should be fixed literally "tightly".
It is possible to apply the projector only when the image dimensions are not too large, the increase will not be required.
Many specialists consider him outdated, although lovers and enjoy them actively and successfully.
Lobzik artwork can be carried out and by sticking to the surface of self-adhesive paper. Using the printer, the desired figure is first printed, after which the sheet passes on the phaneer. On the quality of cutting, the paper does not affect anywhere, but the drawing is not mixed, all lines can be observed exactly.
Cutting from plywood is a very time-consuming process that requires experience and patience, not everyone gets from the first time anything worthwhile. But the exact compliance with all recommendations and rules of cutting allows you to quickly master this art.
A large number of high-quality materials, convenient tools, makes this work quite exciting and not so problematic. Many, starting cutting with minimal skills, are gradually moving to a professional level, creating real works of art.