One of the most simple stages of installation of windows is the installation. The simplicity of such an installation does not mean unavailability of this stage. Plastic or metal foals are protected from the penetration of sediment moisture into the technological gap, which is formed in the place where the window is installed on the coaching profile. The wall is protected from the rain itself under the window. Thus, the installation with your own hands is an important final stage of installation of the overall design of the window. Are there any secrets or nuances of how to install a sampling with your own hands and reliably?
The tump hides the joint and is a protective element that prevents moisture from penetration into the structure. They are produced from galvanized steel, on top of which polymer coating are applied, the sump can also be simply galvanized. Most often used white and brown, in some cases other shades can occur.
Materials and tools
The success, reliability and simplicity of self-installing on the windows is completely dependent on the correct selection of the canvases themselves and the materials used for their installation.How to properly pick up on plastic or wooden windows?
Basic selection parameters
Window sals can be made of metal, plastic or aluminum.
One of the main factors on the basis of which the panel selection occurs is the material from which the window frames are produced. Under the plastic windows, naturally, plastic flows are better suitable, which, most often, are purchased together with the main window design. If the frame is wooden, then it is better to purchase metal galvanized fits that can be painted in any color that is harmonizing with color color of the window frames or the color of the structure walls.
The most important structural parameters of the purchased taming sheets are the following:
- The width that should be slightly larger than the distance from the window frame to the edge of the wall;
- Length, which is calculated from the parameters of the window opening and finishing and decorative of the near square elements;
- The ability or the need to use special plugs for safety or aesthetic design.
Article on the topic: We make a solar water heater yourself
Selective elements that will be installed, it is necessary to choose all the necessary tools and materials for impeccable installation with your own hands.
Instruments
Self-setting is made using the following tools:
For mounting window ties, you will need: roulette, drill, hammer, screwdriver, marker.
- Scissors for metal for cutting sheets of the required length and shape;
- A screwdriver drill for which a extension nozzle may need, as it is necessary to work directly above the walls under the window;
- self-tapping screw (for a wooden frame you can use ordinary, and for metal-plastic windows - with a special drilling end);
- Roulette, marker or other convenient measuring devices;
- Side plugs if the installation is provided.
Featuring such a set of tools and materials, you can safely begin to mount with your own hands.
Features of the main stages
The process of fastening the canvas under the window consists of several simple steps, which can be made with their own hands alone without resorting to help. What do you need to do so that the window space gets its final look, and the wall under the window was not subjected to further destructive exposure to sediment moisture?
The installation of the necessary form begins with the impression of the canvas. The windowspace can be both rectangular and trapezoid or curly shape. And metal galvanized, and plastic sheets are very simply cut by metal scissors. Therefore, having done all the measurements, it is necessary to give the narrow side ends of the cast sheets such a form so that these ends can be easily faced with side slopes. If the installation of the finish plugs is foreseen, then this also needs to be considered by cutting a sheet on the sides.
The figure shows how the correct and improper installation of window ties and the windowsill looks.
Now we take the casting canvas and the appropriate end (on which the curved smooth plane is formed) we will bring under the frame, tightly pressing the flat longitudinal element to the coaching profile on which the entire window design is installed.
Article on the topic: Installation instructions for wooden plinths
With the help of a screwdriver drill, screw the squeeze to the coaching profile. It is very important at this stage, so that the tump is tightly leaving the end to the bottom of the frame.
The space between the web and the outer window sill is often recommended (part of the wall under the refill plane) fill the installation foam. It is not worth doing this, since this procedure does not mean any sense. It follows only a cement solution or a sealing material thoroughly smear the gap between the slopes and the web, if they are not tightly adjacent to each other.
In the end, we establish the finish plugs that are performed both aesthetic and protective function. Especially such protection is relevant on the windows of the first floor. Without plugs, the sump leaf protruding from the wall to several centimeters with sharp edges, can be very dangerous for people passing by people, especially for running and playing under the windows of children. Installing window ties is a process that can be done to each home master.