Adjusting the temperature of the water heating floor is performed to ensure reliable operation of the heating system for the entire planned period of operation, the uniform distribution of thermal energy and maintaining the specified temperature regime in the apartment, which makes it comfortable to find people there.
Setting up a warm floor according to the required parameters before commissioning and supporting these values during operation makes this system convenient for heating various rooms.
The concept of regulating the water floor system
Adjusting the temperature of the water heating floor is the task and maintenance of such parameters in which a certain microclimate will be created in the room.
These settings must be made so that the high-quality and impeccable operation of the system and the temperature-created temperature arranged in the house, apartment or room has been created.
Adjustment can be made:
- on mixing nodes;
- on the sources of heat supply of thermal energy;
- When maintaining a specified temperature mode.
The existing control systems for controlling the temperature indicators of the heat-mall collector are used in accordance with where the setting is carried out, and which method it is performed.
Methods for performing configuration
Adjusting the temperature of the mounted water heat can be made in several ways, which depend on the equipment used in the applied version:
- manual regulation;
- Group setup;
- individual setting;
- Complex adjustment.
All these ways, with the exception of manual, allow you to configure the system using automatic cranes and appliances.
To properly adjust the heating in the house, you must be guided by regulatory indicators.
| Room | Optimal T, C | Valid T, C |
|---|---|---|
| Living room | 20-22. | 18-24 |
| Kitchen | 19-21 | 18-26 |
| Corridor | 18-20. | 16-22. |
| Bathroom | 24-26. | 18-26. |
| Sanusel | 19-21 | 18-26. |
Permissible humidity in residential premises is 60%, but the value of 40-50% is considered the most optimal.
When performing an adjustment, it is also necessary to adjust the flow meters of the warm floor that control the flow of water, reducing and increasing its supply to those moments when necessary.
Article on the topic: 6 ideas of crafts from old soft toys do it yourself
Manual water floor regulation
The adjustment process is completely in manual mode, and all conclusions are made on the basis of personal sensations. In this regard, the risk of obtaining an inaccurate result increases.
Warm water flooring scheme
Therefore, the execution of technological operations during the system setting should be performed according to the following list:
- When using water heating, thermal heads are used under the floor of the parquet and laminate. They are mounted on the feed and return pipelines. Not required to regulate automation, everything is performed manually: an increase or decrease in opening is made.
The system is regulated by turning the valves to the desired result.
- The temperature of the water warm floor is beginning to configure after each loop is filled, and it is impossible to allow air to remain there.
- Before filling in water pipelines under the sexes, you must fill out the rest of the heating system, for which the valves should be opened on the reverse collector and other cranes that provide access to all sections of the system. Then the direct and reverse tubes of one loop are opened until it is full filling. During this, you need to control the release of air from the loop through the air vent.
- Next, the pump is launched to start moving the heat carrier in the pipes. After a few minutes, the temperature at the inlet and output is checked. Pipes to the touch should be warm. Heating is determined by hand. The loop is closed.
- Thus, the coolant of each loop is filling.
- When all the loops are filled, they open all the valves and begin to adjust the flow of water on each of them when studying to the touch of each loop.
- Since the loops are made of homogeneous pipes and the coolant in all loops is the same, then its length will affect the temperature of each of them. Therefore, you need to try to perform the loops of the same size.
Adjusting water warm floors occurs in stages, with an excerpt between operations up to 2 hours, because only by this time the result of any specific actions can be understood.
Group regulation
Group regulation is to reduce or increasing the amount of coolant supplied, in increasing or decreasing temperature indicators, performed in automatic mode, which ensures, of course, the exact result and makes the control process itself.
Adjustment occurs according to the schemes of constants and climate.
According to the CONSTANT scheme, the regulation takes place using the thermal heads mounted on the valves. A simple way to adjust the warm floor, see this video:
If it is necessary to increase or decrease the temperature values obtained during the operation of the underfloor, the system expands or narrows the capillary tube that adjusts the valve hole until the desired temperature regime is established.
How to adjust the climate scheme, automatics itself determines. In accordance with the ambient air temperature indicators, the system automatically determines which temperature you need to get, and for this gives a command to closing or opening the valve.
Individual and complex adjustment
Individual regulation of floors over zones or rooms is carried out using sensors whose installation is made in each room.
Group adjustment does not replace individual, since with the last version in each room installed its microclimate, and at the first one, the entire system works in one temperature mode.
Integrated regulation is a method that combines group and individual adjustment methods and allows you to adjust the temperature in the whole house and in each room separately.
Article on the topic: Trays for storm sewage: concrete, plastic, installation, price