Photo
Shower cabins are a fire off from all sides to take a shower. Outdoor coating under the shower are made hermetic, we are lined with floor tiles. The surface under the device for the shower should be smooth, without borders and borders.
Diagram of the device of the shower cabin.
All construction work at the time of installation must be finished, including pipe and electricity supply, as well as the wall decoration and the seat ceiling.
Installation is followed by an instruction manual for the shower cabin and the rules for its assembly.
How to install a shower cabin
For further operation and repair of the shower cabin, it is necessary to install the product at a distance of 30-50 cm from nearby walls and other plumbers. From the ceiling to the roof of the cabin leave 15 cm of free space. There should be no electrical devices, such as sockets, switches, wires, closer than 60 cm to the soul walls.
When the place for operation of the shower is prepared, the device is unpacked, you can proceed to its installation. For this, you will need the following tools:
- Flat curly screwdriver;
- wrench for 8 mm and 10 mm;
- adjustable key;
- water construction level;
- screwdriver;
- Construction pistol.
Pallet diagram from tile.
During the installation of the shower, the following materials are used:
- sanitary silicone sealant;
- Water supply flexible in a metal braid;
- Rubber Cuffs;
- nipples;
- FUM tape for water.
Before installing the product, in order to avoid possible malfunction due to unfulfilled operating conditions, the water supply communications must be put filters for water purification. The degree of delay of impurities should be at least 100 microns. In case of exceeding the pressure of water in a system of 5 atm, a reduction gear of water pressure reduction is set. Minimum pressure in pipes - 2 atm.
Article on the topic: Patchwork ideas for inspiration: photos, novelties of patchwork sewing and quilting, New Year's ideas for home with their own hands, video instructions
For shower cabins, the conclusions for hot and cold water are put with internal threads, a diameter of 0.5 inches. Sewer tube suitable for operation in the shower must be 50 mm. The cable output is connected to a separate outlet with grounding.
Terms of Use Cabin For Soul
The exploitation of shower cabins begins after the device is fully installed: connected to the water supply system and drain, the electrical block is connected, the wiring is grounded, as the instruction requires. After checking the performance of shower cabins, the mounting seams are processed with silicone sealant to prevent water leakage.
The product is left for 24 hours to dry silicone sealant, after which it can be used, observing the following rules:
The scheme of the structure of the shower.
- Before starting operation, you need to make sure that there is no current leakage and voltage;
- It is impossible to mechanically damage the shower chassis during their operation;
- Device buttons click smoothly without effort;
- The cab must have good ventilation, after use, the product must dry: between swimsuits the shower compartment should stand dry;
- It is forbidden to cut off the electrical wires, modify or change the control unit;
- To clean the surfaces, it is impossible to use agents containing gaseous substances, acetone and ammonia;
- For children and the elderly, the operation of shower cabins should be under the control of adults.
Installing a shower cabin, mounted water supply systems and electrical components can only be prepared professionals. An independent installation of shower unprepared masters will lead to a breakdown of the device and injury to further operation.
How to keep clean shower
In order not to fail, the shower need not only to operate correctly, as the instruction requires, but also to be cleaned properly. For the production of shower cabins, various materials contaminated with water vapor and detergent are used. The closed cab is made of glass or polystyrene, the pallet is usually acrylic, the mixers are chrome steel, and the frames and guides are produced from painted aluminum.
Article on the topic: Electric meter with control panel
Open cabins, where one or two walls are lined with tiles or other moisture-resistant coating, have their own cleaning guide. Caring for the surface with tiles is carried out in the same way as the disinfection of other walls in the bathroom.
Any material is not able to withstand regular purification by abrasive means using metal brushes. Powder mixtures can scratch the surface of the pallet and walls of shower cabins, this will eventually become noticeable, and the appearance of the device will be spoiled.
Mechanical cleaning of the surfaces of the product is very important, droplets remaining on the walls of the cab walls, drops from soapy foam. If you do not regularly get rid of the plaque, lime deposits can be formed, with which it will be difficult to combat.
To remove contaminants, it is recommended to use the following tools:
- scraper from rubber or polyurethane;
- soft rag from microfiber;
- Synthetic sponge;
- Steam cleaner for shower.
Cleaning is divided into:
- Current: After each reception of the soul, you need to rinse the water of the water surface and the walls of the shower.
- The main cleaning is carried out depending on the frequency of the instrument. Periodicity can be from 1 time per week to 1 time per month.
- Intensive cleaning of the entire device or individual parts is carried out using potent chemicals, when one-time contamination appears or a resistant lime bloom appears.
Before using the shower cabin, you need to get acquainted with the instruction manual. There you can find specific descriptions of the control panel, which is equipped with an aggregate. The description there will be information about the purpose of each button, each of which is responsible for its functions. Studying management must for the further use of the appliance.
