Overflow of water from a toilet bowl
The situation is all familiar when the toilet tank in the apartment is noise, it constantly overflows water. There are several causes of malfunction, and in this material we will try to disassemble most ways to eliminate the flows of water in the tank.
Rules for adjusting the reinforcement of the drain tank toilet bowl.
First, you need to find out the reason for the water leakage from the toilet tank. To do this, press over the flour.
If the flow stopped, it means in the tank, the pump was unscrewed, and it is necessary to wrap it in place. Of course, there is one nuance: the toilet tank is arranged in such a way that the overflow nut can be wrapped, only removing the shelf. This situation is still possible - when the nut sticks to the surface of the tank, to eliminate the leaks, it is necessary to rotate clockwise in order for it to take the right place. If the nut naved to the surface of the tank and the water continues to flow, you need to do the following:
Scheme of the device of the exhaust valve of the modern toilet bowl.
- If the nut is not completely unscrewed, but a gap appeared between the bottom of the tank and the outer surface of the tank, overcap the water intake and drain the tank. Wait until the walls of the toilet bowl dry, and sweat the gap to the resulting clearance. Next, this place needs to pour paint. If you use oil paint, then in order to speed up drying, add a solvent into it. After repair, give paint to dry, and only then you can use the drain tank toilet bowl.
- If the nut is unscrewed to the end, overcoat the water supply valve and drain the toilet tank, dismantle overflow and wrap the seal on its thread so that it gets into the hole at the bottom of the drain tank as possible, and mounted everything in your place. For better tightness, lubricate the place of the oily paint seal and wait for it drying.
Article on the topic: How to remove windows on the balcony: Tips and recommendations
The hole of the overflow in the toilet tank must be open and not clogged, otherwise the water will overfill the tank and sticks to the toilet floor, it sometimes happens when the tank free overflow. Cause of this fault in disruption of the installation of a flip of a toilet bowl, due to the weak shelf and toilet fastening bolts. The consequence is the roll roll, which is why overflow is above the tank walls. If the fastening bolts are not able to wrap due to their corrosion, you need to shorten the level of overflow. To do this, you need to make a recess from the upper edge and to the desired water level. The recess can be made with nippers or a heated knife.
Float valve clogging
Scheme of the stabilizing float valve for a flip of toilet bowl.Another problem that occurs with a float valve in a toilet bowl - its clogging as a result of the fact that the water is constantly overflowing through the drain (the plum tube is already mounted in some designs). The work of this valve is extremely simple: when the water is recruited, the float pops up and the built-in lever moves a plastic or brass plug, the plug in turn overlaps the rubber gasket of the nozzle through which water is supplied.
If there is no overflow in your tank, which happens very rarely, then you need to overlap the flow of water, unscrew the flexible eyeliner and disassemble the feed valve. After that, you need to remove the plastic plug, break the pliers a locking pin and get it. After that, it is necessary to hold the valve body with one hand, and the other is to pull the float holder from it.
You will see how the locking lever will be pulled out with a rubber gasket, which is likely to fall out. If you then look into the valve body, you will see the through hole through which water passes into the toilet tank. If this hole is clogged, you need to clean it, use a long needle or wire for cleaning. After cleaning, you need to check the lever with a gasket, usually the gasket to this point is already being sold and cannot perform your locking function.
Article on the topic: Wall clock in the interior: Large and small, classic and unusual (70 photos)
There are several outputs from this situation: replace the gasket; replace shut-off valve; Align the installation site with a knife and emery paper, after which it is placed on the place of installation cut out of the bike chamber with a gaze form; Turn over the gasket, she can still serve for some time.
Increased water consumption
Schematic diagram of the device of the float valve: 1 - clamping washer; 2 - gasket; 3 - saddle; 4 - membrane; 5 - rod; 6 - Float lever; 7 - lever axis.
What if your toilet consumes too much water? There is a simple way to reduce consumption in the drain tank is an adjustment of the float in the toilet so that the valve overlap water before. If the lever is brass in your bowl toilet bowl, simply adjust it, after lifting and lowering the lever - you will see at what level it overlaps the water supply. If the tank design is more modern and plastic lever, carefully inspect its design. To adjust the float level in this case, either a fastener screw, which changes the bending of the lever, or a ratchet fixing the float in one of the positions.
In this article, we cannot qualify for a complete analysis of all the problems arising from the toilet tanks, since new models with absolutely other mechanical parts and constructive "children's diseases" constantly appear on the market. But in most cases you can use a careful study of the product instructions to eliminate malfunctions, and a small list of tools and materials.
From the tools you need to have:
- gas key;
- Passatia;
- A sharp knife.
Necessary materials: a piece of cycling rubber for the manufacture of pads and in the case of replacing any mechanical part of the drain tank - its rem. Set or spare part assembly. Good luck to you in your repair!
Article on the topic: We do a self-leveling transparent floor