Curtains are the face of the room. Therefore, their choice must be treated very seriously. Now almost anywhere in the sale of fabrics for curtains is offered for a fee and tailoring curtains. However, it may not always have enough money to tailor, especially if the fabric is quite expensive.
Curtains on hinges made with their own hands will cost much cheaper of the ready-made store.
Seam the curtains do it yourself even more pleasant. After all, you can always be proud of your creation. Having learned to fulfill this kind of work, you can help others, earning money. Therefore, it is advisable to consider how to sew curtains on the loop.
Sew curtains on loops - the best option for beginners. Unlike complex lambrequins and ruffles, such curtains are much easier. At the same time, they will look very beautiful, subject to the correct selection of the material.
Cutting and tailing fabric for curtains
Scheme of wide fabric loops.
We gradually consider the option how to sew curtains on hinges for a standard small single window. The emphasis is on the fact that the curtains will close the window and do not reach the floor (the estimated dimensions of the window: the height is about 1.3 m, the width is approximately 1 m).
The first stage will be the preparation of fabric and its cut. It is necessary to take a large piece of fabric for curtains with dimensions of about 150x280 cm. Fabric decompose on a flat and clean surface. Before marking, it is desirable to light it slightly so that measurements and patterns are more accurate.
Take chalk (you can replace with a sharp piece of soap) and a long line. Find along the long (280 cm) of the middle of the middle, which in this case will be 140 cm. Make a few marks and carry out a solid line. It will be a cut slicer line and split a solid cloth into two curtains. Babe carefully cut the cloth.
Article on the topic: Types, ways to decorate windows
Now it is necessary to note all the necessary points. Please note that the fabric is only needed on the sides where the edges are not finished. Often you can see in stores such canvas for curtains, where there are already beautifully decorated or side edges of the curtains or lower part.
Packages need to do two. It will serve as a reliable binder, as you can be sure that the fabric is not fruishing. First, from the very edge, we postpone about 3 cm and make marking in several places, after which we combine them with a solid line. Now we are postponing for another 3 cm and make marking and line.
It will turn out two markings from the edge of the curtains. On markups, then you need to bend curtains for the binder. Having made the tissue with such a double way, you will receive a high-quality cloth that does not break through time. This method markup for allowances are made on all sides of the curtains where it is necessary.
Making loops for curtains
Loop size scheme.
The next stage of the work will be sewn the loops for fastening the curtains. Consider how to sew the loops are the simplest and practical. It is necessary to draw a rectangle width of about 12 cm on a piece of cloth and about 15 cm long. The length of the rectangle can fluctuate depending on how the cornice diameter. If the length of the rectangle is 15 cm, then when folding in half and pod, the height of the loop will be 7 cm. This is the best option, because so usually the curtain in the room looks best.
After marking, cut the rectangle. Similarly, there are another 17 such figures. The total number of loops will be 18 pcs. You can take another number of loops, the main thing is that the curtain between them happens the same distance.
Now go to the processing process of the loop for the curtain. Take a rectangle and fold it neatly twice in the face. Now it is necessary at a distance of approximately 0.7 cm from the edge to see it on the machine with a reliable seam so that the rectangle is connected. It is better to take two times, but then you will need two markings from the edge of 0.7 cm each. As a result, it will take about 1.4 cm. So you need to sew each rectangle.
Article on the topic: Four-sheet roof for a gazebo with your own hands, how to design and build it
After the end of the work, the stitched hinges will need to be turned on the face and disappear with the iron so that they become flat and smooth on the sides. Next, proceed to the processing of the remaining edges. Also done double champions and striking. After that, it will be necessary to fold the finished strips by half the length and connect them with a conventional line or a small gripping seam. It turns out ready already loops for curtains.
Methods of fastening loops to curtains
Now the last stage of work is the fastening of the loops to the curtains. There are many ways. Consider the two simplest methods: this is the mount with the help of hiding tape or the so-called pocket on the curtains.By type of pocket
Types of pickups for curtains.
Take the finished canvas of the curtains and decompose on a flat surface. To work it will take the top of the curtains. From the top edge on the front of the fabric you need to mark the line at a distance of 2 cm from the edge. Then, from this line, mark and read another 2 cm. Look all the chalk or soap, be sure to use the ruler. The lower line will serve as a bend seat, and the upper one - the threshold for overpowing the loop in pockets. This option is optimal, as the loops will not be at the very top edge of the curtain, which will look much more beautiful.
If you bend the curtain exactly at the bottom line face inside, so that the wrong insight can be seen, it will turn out to be a pocket. Loops will be inserted into it. But until you need to sew anything. Take the first loop and insert into your pocket, then step in the width of the loop and about 0.5 cm from its edges so that the pocket closes on the place of the loop. You need to scribble without letters, making everything clearly around the edge, so as not to pick up the curtain too much from the height.
Article on the topic: Photocollage on the wall: Ways to create with your own hands
Now from the loop, retreat at the desired distance and in the same way, enter the second loop in your pocket. If you are not sure about the accuracy of the distance calculations between the hinges, you can first note, and then sew. It will be more convenient because with the final reliable connection of the loop with pocket, it is not necessary to sew each loop separately.
When all the loops are stitched into the pocket, it is necessary to open the curtain in this place well so that it looks smoothly. It is best to do it iron with a sprayer.
Using a tape
The second method of fastening the loops to the curtains - with the help of a hiding tape. This method is considered simpler and practical. No need markings and marks. The only thing that will be needed is to be purchased in the store a special ribbon or faucet. The height of such a tape should be 2 times more than the loop allowing, which will be repaid under it.
The tape is sewn from the wrong side. First, the lower part of the tape is striking, after which the curtain is stacked on the table, loops are inserted between it and the ribbon, closed with a ribbon, everything is passed on to the top. You can also first sew a loop to the curtain, and then from the wrong side to sew a tape on them.
So, sew curtains on the loops are easy if there is a sewing machine. The feature of such curtains is that the loops can be of another color - different from the shade of the main product. It will add contrast and brightness to your window.