Gosty normalize a lot, including how it is possible or cannot be distinguished by the plots. For example, the standards are prescribed to distinguish the neighboring sections with transparent fences. Since the intelligence is usually long, it is desirable that the fence was inexpensive. Actually, the choice is small - a fence from the grid of a chain or woven. The woven though cheaply, but is extremely short-lived, so it remains only a net fence. In general, it is generally correct to say "fence from the chain grid", but for the ear we are habitable to incline.
Popular and inexpensive - chain fence
No matter how the fencing is called, and it has a solid number of positive parties. The first and important plus is low cost. This applies to both the fill - grid and the rest of the design. To pull the grid, the foundation is not required. It is enough to drill the wells about the meter, insert a pillar and, falling asleep rubble, is good to seal it. All, no concrete work. On most soils, this method of installation for this filling is "five".
Constructions and installation methods
The fact is that the fence from the chain grid refers to the easy. Moreover, it is lightning both for its own weight and in perceived wind loads. Whatever strength winds do not blow, the pressure transmitted to the grid remains insignificant. Due to the low weight and can be used such a pillar installation technology: in the well, under the backing of sand or rubble, without concrete. Moreover, it is such a fence without problems even on bunched clay soils with a high level of groundwater, and even with a great depth of freezing.Without guides
That's how it works. We are talking about the most simple design: just pillars, between which the grid is stretched. As you can see, the pillars are buried to a depth of less than a meter. What happens to such a fence on the soils, normally reducing water? The whole, located near the pillar of water, goes through the sand or crushed down, on the bottom of the well. There it goes natural way - seeps in below the lying layers. Even if the frost, and the sand or crushed stone around the pillar, the moisture contains is not enough in order to have any significant impact on the pillar.
The simplest design of the slaughterhouse
On clays and sublinks, you can use the same principle, only to fall asleep by gravel. And be sure to pour 10-15 gravel centimeters to the bottom of the wells, and only then install a pillar. What happens in this case. Water is also accumulated at the bottom, but it goes very slowly. It may well happen that by the time of the freezing, the crushed stone will still be wet, or even in water.
What will happen then? It will freeze and will be tough. But since the soil also freezes, he presses on crushed stone. Considerable strengths, and the ice is broken, crushed stone becomes mobile and compensates for most of the pressure generated by the soil. As a result, if the column movements occur, they are very small - from a few millimeters to several centimeters. Since the design is a non-rigid, the grid will easily transfer it, without any harm. After everything fades, the posts will fall into place. But such a scenario is only if they are exhibited perfectly vertically. Otherwise, pillars can bendered and have to fix everything.
With guides (brokers)
Sometimes, that the fence is more solid and better kept the shape, two longitudinal guides are fixed to the columns. May be from the pipe, and they can - from the bar. Wood, like a plastic material, transfers the soil movement is remarkably, but the welded pipe will create additional difficulties.
Fence from grid Rabits with metal guides
The degree of stiffness of such a fence is higher, and when it is bent if the columns are squeezed, it is quite possible that some of the pipes can and tear off. To prevent such a situation, you will have to be buried below the drainage depth in your region. Everything else remains in force: the hole is 15-20 cm deeper than it is required, on the bottom of the crushed stone, then the pipe is inserted, covered with a good rambled rubble.
Sectional
There is another design of the fence from the chain grid. A frame is boiled from the corner, which then stretches the grid. Finished sections are welded to the posts.
Article on the topic: What to position between the windows?
Sectional fence from Rabita
As it is clear from the description, the design is also quite tough. This means that on the bunched soils (clay, loam), it is necessary to bury the pillars by 20-30 cm below the depth of the soil; but everything is also desirable without concreting. If you are rubble to the concrete, the likelihood that the "extruded" post increases many times.
Types of grid Rabits for fence
Even such, it would seem, simple material as a chain grid is different. Moreover, the difference is solid and in price, and on the service life.
- Neocken. The cheapest material, but also the most short-lived requiring significant expenses for maintaining a normal type. Immediately after the installation, the grid must be painted, otherwise it is delayed. Painting has to be renewed annually, whether every two years.
- Galvanized. It is much more expensive for the price, but painting does not require and for a long time.
Plasticized Rabita Mesh - Metal in Plastic Wrapper
- Plasticized. A layer of polymer (plastic) is applied to the metal wire. This kind of chain racial appeared so long ago. It is even more expensive, but the kind is the most attractive, the service life is even more. When choosing, pay attention to the thickness and rigidity of the wire, which is under the coating. Normal with great difficulty begged under the fingers. If it is easily bent, then it will be difficult for you to stretch it normally.
- Polymer or plastic. It is made of polymer, has additives that increase its resistance to ultraviolet. Painted in different colors, has different shapes of cells. There are more familiar, similar to the cells of ordinary stacks, rectangular and even round holes. Sometimes this type of grid is called "Garden Plastic Fencing". On the bite with the neighbor can be used as a fence from the street - will not go: insufficient strength.
Plastic or polymer mesh - 100% consists of a polymer
In addition to different material, the slave has a different cell size. It varies from 25 mm to 70 mm. The greater the cell, the cheaper the grid, but the smaller carrying ability it has. If you put a fence from the chain grid on the ground with a neighbor, take mostly the average link - from 40 mm to 60 mm.
What to pay attention to when choosing a grid
Carefully inspect each roll. The edges should not be curved. The upper and lower cells must be covered with "tails". Moreover, it is desirable that the length of the bent part was greater than half the length of the cell. This grid is easier to pull.
Edges must be smooth and curved
Pay attention to the thickness of the wire, how much smooth cells, how the gadko they fall. All deformations are a sign of low quality.
If the chain grid in the polymer coating, specify the warranty period that the manufacturer gives. The cheapest, little that the wire is often bend, use another ordinary plastic, which under the action of ultraviolet after a couple of seasons becomes fragile and starts to pour. Normal coating can stand up to ten years and more. Therefore, in this case, it is not worth cheap.
How to make a fence from the professional sheet, read here.
What to use pillars
Several options:
- Wooden poles - from a bar or logs. The cheapest, but also the most "fast-carrying" option. Antibacterial processing is required before installation. The best option is a special protective impregnation. To save, you can paint the above-ground part, and the one that will be buried, it is better to heat up: immerse the pillars in the container for several hours. Before installing in the well, it is possible to wind up this part to the ruberoid.
Fence from the chain grid on wooden poles
- Metal poles. Can be made of a round or square tube, a metal corner. Wall thickness 2-3 mm, pipe diameter on average 50 mm, section profile 40-50 mm, angle shelf - 50-60 mm.
- Concrete poles. The most uncomfortable option is the option: it is too difficult to mount the grid to them, and it is difficult to install it hard. In addition, the resource of the strength of the reinforced concrete will not be in demand: too small load creates a fence from the chain grid.
The most convenient option from all named is a profile tube, and better - rectangular cross section. It is easy to mount to it and the grid, and you can welcome, if necessary, hooks or wire. If possible, put such. The optimal section for the pillar is 25 * 40 mm or so. Larger cross section to take is not worth the fence.
Procedure for installing column
First set posts at the corners of the site. If you need to disperse only one side, one pillar is installed at the beginning, the second is at the end. Strictly checked their verticality in all planes, the height is adjusted. At the very top and 10 cm above the ground level, two cords are stretched. They are put on the rest of the pillars. The top shoelace is aligned, the lower serves to facilitate the orientation: applying a plumb to the point on the top thread, you can find a place in which the hole will be clogged.
Installing pillars under the mesh fence
Stroll installation step - 2-3 meters. Less - too expensive, more - it makes no sense, there will be a grid. When installing a grid without guide wire, it makes sense to put pillars every 2 or 2.5 meters. So the grid is easier to tighten without sagging. For other models - with wire, sluggings (guides) or sections - a step may be 3 m.
Example of enhancing an angular rack
If the grid is tightened between the columns, the extreme has a considerable load. So that they are not "led", they put bodies. They are exhibited, swing, weld to the installed post.
Installation of grid Rabita
It only first seems to have a fence from the chain grid simply. As soon as you begin to think about how to fix the grid on the post, how to pull it, everything is not so obvious and simple ... first about general rules. The grid is attached to one of the angular columns. Fasten at least four places. In principle, you can simply fasten the wire by passing it into the cell.
Methods Maintaining Mesh to Post
Method, simple, but not the most reliable. If the fence in the country, during the absence of the hosts, the grid is easy to remove and carry.
You can at least in the first and last post, consolidate it more reliably. For this, they take a steel bar with a thickness of at least 4 mm, they make it through cells, weld to the pole, grabbing each 40-50 cm (in the photo on the left).
Another way: to weld to each post three or four rods with a diameter of 6 mm. The grid is attracted on them, they are bent.
Private rods, pull the grid, bend
If you still paranitate that the grid will take off, you can drill two through holes in the post, insert the rod curved in the form of a horseshoe - U, capturing the grid "back". On the other side, where the ends come out, twist them and split, or cook.
Tension
There is another problem: how to pull the grid. If the design is simple - without slightly (transverse guides, which are fixed between the columns), you can simply stretch the grid from one post to another. Just note that it is necessary to securely securely to each post. Fasten first through one, and then intermediate - unsuccessful idea: there will be uneven tension and sagging.How to pull the chain grid so that there is no savory? To stick the bar, take on it and pull it all weight. Stretching will be quite significant. It is necessary to work with the assistant: one pulls and keeps, the second crepit.
With wire
This kind of fence is good because it is raised quickly. But the upper edge can be saved. If someone climbs through it, the top will unambiguously replete. It is unlikely to straighten it. In order for the top not savage and not "rolling", through the first row stretch the wire, you can steel, and it is possible in a plastic shell - so as not to rust.
So that the grid has not saved, stretch the wire from above
If the wire is used, the technology can be simple: to make a loop at the end, throw it on the extreme post. Washed the wire trying to pull, the pillar in two or three make another loop, turning the wire around the pillar. So until the end of the span. With the use of muscle strength, it will not be possible enough, and wire will inevitably offer. It is easy to fix. Take a thick metal rod, and make a twist with it, pulling the wire. One twist little? A little further make another one. So pull up all the "spans". After you can begin to "pull" the grid, tieting it to the stretched wire.
If you spend the top of the "ears" post - a metal bar with holes, a wire can be mounted on them. Stay a piece of 2-3 meters easier, but the work goes slower.
Still method of fixing wire
You can also use special wire tensioners. Then fixing the wire on one post, on the second it is passed into such a device as in the photo. It is attached to the clima, and then with the help of the key, overwhelms the drum.
Special wire tensioners
You can use a cable and tallies - hooks with clips (in the hardware store). On the one hand, the cable is twisted around the pillar, clipped with a clip. On the other posts talp. Its middle part has a thread, thanks to which it is possible to pull the cable.
Talp with a cable - another option
Since the cable is more flexible, it can be skipping through the links. Each will be too long, after two or three cells - normally. Another point: take a cable with a polymer shell: will not rust.
With a welded rod
In the upper cell, or slightly lower, they make a steel bar with a diameter of 6-8 mm. It is cut into pieces equal to the distance from one post, to another. The stretched rod welded to the post.
Warded rods, extended through cells
Pay attention to the top of this chapter. On this photo it is clearly seen that it has already begun to bloom. This is exactly the reason why you need to take a grid with curved ends. It is simply not afraid of it and even without wire or the rod is well holding the edge.
With the signs (guides)
In even more stringent structures after installing the columns, the glory welded to them. These are transverse pipes or wooden strips attached between pillars. The guide may be alone, and maybe two, and three.
Fence from the chain grid with the glory
As you can see in the photo, it is possible to mount the grid in this case using a wire. It is quite obvious that all methods described above can be used. The only difference is that the mesh is attached not only vertically, but also horizontally. In the photo below, another method was captured - with plates screwed bolts, the ends of the splock. This method can also be used when fixing on columns.
Another way to fasten the challenges to the metal columns
How to make a wooden fence-braided here.
Decoration of the fence from the chain grid
No matter how pleased the fence at first, after some time there is a desire or decorate it, or to make less transparent to close from curious eyes.
The first method is the most obvious - plant plants. If the neighbors do not mind, you can let the basins or any other annual or perennial plants.
The most natural way is to plant plants
If you want to just decorate your fence, you can make an "embroidery". Cells have the same dimensions, so that it is possible to embroider as on the canvas. Materials for embroidery Two: Wire and color twine.
Decorated fence from the grid Rabita looks incredibly beautiful
Color twine is good because you can "embroider" colored pictures. Any that seem relevant to you.
Embroidery on the grid with colored twine
Like this)))
Not very aesthetic, but quite an effective way - to pull the camouflage or dialed grid. They are good these ways that they require a minimum of effort: pulled out, in a pair of places picked up.
A camouflage mesh on the fence significantly reduces the viewing of the site
The shading grid is almost opaque, and the wind load will not change hard
The same effect is achieved if twisted in the cells of the twig or reed. Minus such a variant in high laboriousness. Time will need a lot.
Welcome to the mesh reed or thin twigs
Reduced manufacturing costs allow ready reed mats. They are sold in rolls. All you need is to roll and consolidate. But the cost is much higher than that of the previous version.
Reed mat
Another way is to use artificial hivo sold in rolls. It is used in the manufacture of baskets and wreaths, but it is quite possible to adapt to the fence.
Green Wall - Rabita Mesh Decorated Artificial Cheese
Not so long ago, another way of decorating and, at the same time, a decrease in the viewing of the fence from the chain grid is a photodette. This is a drawing applied to the polymer mesh. Sold with rolls (for a tensioning fence) or fragments (for section). Fastened using chosen and wires or clamps built into the surface. Approximate effect can be estimated in the photo below.
The photostress for the fence from the chain grid and decorate the fence, and will close the site from curious eyes
Article on the topic: Wallpapers Photo 2019 Modern: wallpaper design, photo wallpaper in the interior of a small kitchen, photo gallery, video