The flow from the crane has long been "proverbs in the town" - a symbol of those small domestic troubles that cause major homemade scandals. And the problems of the shower cabin mixer are fraught not only by the deterioration of psychological "weather in the house", but also the probability of water leakage on the ceiling of the neighbors living below.
Connecting the electrical shower circuit.
In this case, to wait for inspiration and postpone the repair of the shower on "somehow later" is not very profitable. The time for repairing the mixer is required at all, and all the work can be performed independently, having "in service" elementary working tools:
- hexagon;
- flat screwdriver;
- pliers.
Device of the shower faucet
The mixer is a sanitary mechanism, with which the water current is adjusted, the water of the desired temperature is obtained by mixing the hot and cold jet, and also give the direction of water to the shower.
The device of a single-art mixer.
The components of the mixer:
- The housing made of brass with a decorative electroplating coating. Shower cabins of most manufacturers, including their hydromassage modifications, consist of interconnected tubes of the mixer housings and water distributor.
- Water mixer cartridge. Standard plastic cartridges with a size of 35-40 mm are sold in stores of sanitary goods.
- The clip of this cartridge that performs the role of the holder. Its inner thread is intended for winding on the body, the inner partition is for fixing the cartridge on the surface of the body, the outer thread - to secure the crane on the console console.
- The distributor cartridge, the so-called diverter, held by the nut in the water distributor nest.
- Flywheels of the mixer and water distributor.
The only trouble in eliminating the breakdown of the shower crane is the inability to change the details collected in the unintended cartridge. But it is for this reason that the repair itself is very simple to be performed, because often it is often necessary to replace the cartridge.
Article on the topic: Arbors and Pergolas: What is the difference
Types of crane faults and their repair
Faucet diagram with ball mechanism.
Defects in the operation of the distributor (upper) cartridge:
- Proceeds under the switch. There is such a crane breakdown for various reasons. With a crack of the cartridge housing, it is necessary to replace it. With a slightly twisted cartridge fastening nut - suspender. When wearing rubber rings on the roller of this cartridge - new rings. But if leak is caused by insufficient sealing of the cartridge in the nest, it will be necessary to replace the entire mixer. It is not easy to dismantle it, you have to move the shower cabin, as it is fixed with a nut on the outer back wall.
- The soul modes are not switched or switched tight, while the crunch is heard. It happens when the cartridge plastic breakage. Consequently, it is necessary to replace it.
Defects in the operation of the mixer cartridge (Lower):
- Water does not overlap;
- Water is poorly mixed;
- The lever is too tight or too light.
Repair In all these cases has one option - replacing the cartridge.
The breakdown of the closure, the destruction of the partition. This is the saddest incident that can happen to the owners of shower cabins. With such damage, a powerful water jet, and both cold and hot, beats where it is pleased with it (since there is a pallet in the shower). You should urgently overlap water and run to the store! It will be necessary to immediately replace the mixer.
Replacing the Cartridge of the Shower Mixer
The repair of the mixer usually implies with just replacing the cartridge. Alas, a rare cartridge after operation of the shower cabin for several years can withstand the "quality" of our tap water with its rust, lime, sand, all sorts of other elements of the Mendeleev table.
First of all, you need to overlap water on a shower cabin with cutting valves. Then proceed to dismantling the mixer. Remove the handle of the power on and mixing (it can be in the form of a lever or have a ball shape). To do this, the plastic plug button is removed at the handle and the clamping screw is spinning. Decorative lining also remove. So, at the bottom of the mixer is removed by pulling to yourself, a round plate, and at the top - unscrew the nut that holds the decorative panel.
Article on the topic: Pipe for a warm floor: what better, expert advice
After preparatory work with the help of a flashlight inside the unit of the node to ensure the fact of the cartridge breakdown. On the rear wall of the shower cabin, carefully unscrew the nut, remove the assembly assembly and sealing rubber, which seals the rack on both sides. Next, clean the surface, apply a new layer of special sealant for plumbing and tightly put a new cartridge in the grooves. By climbing the clip and setting the sealing rubber lubricated sealant, fix the design with an outer washer and nut on the back of the shower.
After the assembly is completed, the mixer will again fit work, giving all the household moments of pleasure from pleasant water procedures.