The difference between the ball crane from the usual
Appearing relatively recently in the domestic market, the ball crane has become one of the most common faucet designs. The ball valve successfully passed into everyday life and use it both in the kitchen and in the bathrooms. As you know, nothing is forever, therefore, even such a reliable mechanism like a ball valve, may fail and give to flow.
One of the common causes of the leakage of the ball mixer in the kitchen is to hit the trash in the cartridge, for this you need to disassemble the design and clean it with the help of a sponge and detergent.
If the faucet is dried, first you need to get acquainted with his device to understand how to repair it.
The device of the ball crane is quite simple, although somewhat more complicated than the valve crane. Water mixing occurs in the core in which a ball having three holes is installed. This bulb is made of stainless steel. In one of the holes, hot water comes, to another cold, well, in the third hole, the water of the temperature is supplied to the user.
The ball is installed in the sleeve cartridge that is easily removed from the case. For sealing, the ball is placed in the rubber saddles, to which the ball is very tightly adjacent due to the actions of the water.
Externally, it looks like a mechanism with one swivel lever. Turning the handle in the up-down direction, you can adjust the strength of the water pressure. And turning to the right and left, you can adjust the temperature of the supplied water. Ball cranes distinguishes not only simplicity and ease of operation, but also the high reliability of the mixer, which is facilitated by the simplicity of the design. Consider some causes of leakage.
Article on the topic: Choose fashionable wallpapers for the 2019 hall: photos and 7 varieties
The reasons why the ball crane flows
Scheme of the device of the ball crane.If with conventional valve cranes, everything is more or less clear, then problems may arise with ball cranes. Such a crane flows completely different reasons. Having learned why he flows, quickly eliminate the problem will be easier. An ordinary valve crane often proceeds due to wear of the gasket or the gland. And the repair of such cranes does not cause special difficulties in most men. But on the design of the ball valve does not have glands and gaskets. Although it does not mean that he does not happen! Just the causes of leakage, which means that repair methods differ from the valve cranes. Therefore, starting the mixer, and not finding the pads there, many are confused and do not know what to do next.
The most frequent problems with ball valves, if not to take into the calculation of the factory marriage and mechanical damage, become leaks, the problem of temperature adjustment, as well as the weakening of the pressure.
If the crane flows, the reason for the hit may be the hitting of garbage, which in the kitchen is more than enough, in the cartridge or the failure of any of the parts of the system. It can be a crack on the housing, and clogging of the cartridge, and clogging aerator, and wear of the gaskets on the spool. All of these faults require repair. And it is necessary to prepare to it, and should also be carefully followed by instructions, since the inner device of the ball crane is extremely fragile and it is easy to damage.
Since clogging brings to the leakage of the ball crane, in any case it will be necessary to disassemble the mixer for current cleaners. If during the disassembly, some kind of malfunction will be detected, it can be eliminated. Everything is not so difficult, the only thing that is really necessary is caution.
Article on the topic: Ergonomic cabinet to the balcony with the role of shutters: convenience and compactness
Repair of the ball crane
List of tools and materials
To repair any mixer, it would be nice to get the following set of tools that should be at the plumbing at hand:Mixer repair tools.
- adjustable key;
- Screwdrivers, flat and cross;
- wrench, etc.
Often this uncomplicated set is quite enough to repair the mixers. You will also not be superfluous and elements that can be found in the plumbing bag. Slices of rubber can be useful, from which you can make new gaskets, and fluoroplastic sealing tape that replaces the liners. Even for removal, a regular sponge and detergent will need to be removed inside the garbage and dirt. Experienced plumbers use litters that are covered with sinks. This is done so that a randomly flying tool damaged the sink. For this purpose, a rag or a piece of foam rubber is suitable.
Step-by-step repair manual
In order to eliminate the problems with the current crane, it is necessary to start overlapping the water supply to begin. Often cranes are in the bathroom or in the toilet. The valves must be rotated 90 degrees, relative to their present position or turn clockwise until it stops.
The main complexity of the repair of ball mixers is the presence of unintended parts. These details are included in the cartridge. This means that it will not be possible to replace them separately, you have to replace the entire cartridge completely.
Speaking about the analysis of the ball crane, it is safe to say that you will be useful to the limit accuracy. Let's now consider the most ideal option when you only need to clean the mixer. But for this you need not only to disassemble the mixer, but also to collect it correctly, while without damaging the detail of the mixer.
Disassembly of the ball mixer
It is necessary to observe the following sequence. To begin with, unscrew the screw, locking the lever. Then it follows how to carefully remove the lever of the crane. Next, you need to promote the threaded connection. Before us is the dome of the mixer. It needs to be removed as well as under the plastic seal. From the plastic seal, you will need to remove the sealing gasket.
Article on the topic: The better cutting metal-plastic pipes?
Scheme assembly ball mixer.
At this stage, pay attention to this gasket if it is cracked, it is clearly replaced. If not, at least it is necessary to clean this gasket, removing the collapse of it.
The next step will be the extraction of the ball. Again, with visual inspection, determine how much it is possible. If the ball is badly damaged, it will be necessary to replace it. Cleaning the ball, go to seals, fixing the ball. They should be carefully removed, pushing a thin screwdriver. If the seals are at least a bit damaged, they should be replaced with mandatory.
Replacing all the details of the details need to lubricate seals. Then you should collect all the details of the mixer in the reverse order.
What if your mixer continues to flow? Perhaps the case in the mixer cartridge. In this case, it must be replaced, as it is impossible to disassemble or fix it.
Very often a ball-structural mixer flows due to clogging of the cartridge of small garbage. In this case, the mixer's own repair will be consistent with the complete replacement of the cartridge. But this process requires accurate consistent actions.
First you need to remove the mixer lever regulator. Then you should shut and drain the water. When there are no more water in the system, it is necessary to dismantle the nut, which is fixed by the cartridge. Then drove the old cartridge, replace it with a new one, while tracing so that the sealing rings are on the cartridge. Everything is very simple. By installing a new cartridge, you should fix it with a nut. Then you need to assemble the mixer in the reverse order.