Half the garden, download water into the tank from the well, river, lake, or even from the well - all this can dubbed baby pump. What is nice, it costs quite a bit, however, the characteristics are modest, but for watering the garden or providing water a couple of cranes is enough.
Has modest sizes and weight
Application area
Submersible toddler pump has a low price, suitable for pumping clean water. Highly polluted water is better not to download - quickly burns. Apply it in the following cases:
- for watering the garden;
- for a set of water in storage tanks;
- For water supply at home, but with certain restrictions (about it is slightly lower).
Switching water submersible pump kid can from a well, natural source - pond, rivers, lakes. It is suitable for distribution of water from tanks. You can use it for wells, but with reservations. Since the type of vibration pump, it creates fluctuations in the thickness of water, raising the smallest particles (Il, clay, sand) from the bottom and sucking them. If, in the case of a well, this is nothing, except for opaque water, does not threaten, then when using a toddler pump in a well, it can be faster. In any case, this is a common opinion.
So that in the well or well of the submersible pump, the baby did not fight about the wall, rubber shock absorbers put on its body
Manufacturers in recommendations for use indicate the minimum diameter of the well or well - 90-100 cm, some models (kid 3) can operate in sources with a diameter of 70-75 cm. However, they are used in very narrow wells. The main thing is that it goes there. But at the same time, he beats about the wall of the well, creating additional vibration, and threatening to chop the casing or damage their own body. To reduce the bias on the body, rubber rings are put on (in the photo above). They solve the problem.
Manufacturers
The name "Kid" and "River" has long become nominative. So today they call small submersible vibration pumps. Initially, they made them exclusively in Russia or in the near abroad, but today there are plenty of Chinese "kids" in the market. In general, there are several manufacturers of such pumps in Russia:
- In the city of Livny in the Oryol region and in Balev, Vladimirskaya produce precisely kids. Most goes with the upper water fence, kids M - with the bottom.
- Kids are produced in the Moscow region Klimovsk.
- In Kursk and Kirov (Plant Lepse) produce pumps of the same type, but under other names - Aquarius.
- In Bryansk (enterprise, a poplar) produce Springs. With the same name produced submersible pumps in Chelyabinsk, and another bison firm.
- River units produced in Mogilev (Belarus).
Different names and firms, some differences in characteristics, but all this submersible vibrating pumps type kid
The remaining brands are Chinese. How to determine? Carefully consider packaging and passport. If this is a Russian manufacturer, must be the address, the name of the enterprise, the list of service services, etc. If there is no such information, this is a product of the DPRK.
Specifications
As already spoke, the submersible pumps kid have a small capacity - mostly about 250 W, that is, it is not able to create high pressure. Their clones with other names can be found a little more powerful.
What else is important - the rise height is for what distance water can roll. In technical characteristics, it must be more than that you need by about 20%.
Pay attention to the power to which this model is calculated. Typically, it is 200 V with possible small deviations of about 5%, but the real estimates are that 240 V can be in the network, and with such voltage the pump with such characteristics is burning. Exit - to put a stabilizer or look for a model with a higher operating voltage (a decrease from the worker does not affect the operation, power drops).
The length of the electrical cable can be from 10 meters to 40
This indicator is important as performance. It is usually indicated in liters per minute or per second. This value shows how much water an aggregate is able to flow under normal conditions. For this type of equipment, this figure is quite small - about 400 ml / s. Such a submersible pump kid can provide with water one point of water intake - one irrigation hose or crane in the house. For something more, it is not capable without additional equipment.
| Name | Water fence | Idling / overheating protection | Power | Performance | Lift height | Diameter | Immersion depth | Price |
|---|---|---|---|---|---|---|---|---|
| Malyshm n 1500 poplar | Upper | no Yes | 240 W. | 24 l / min | 60 M. | 99 mm | 3m | 1741 rub (plastic) |
| River-1 Mogilev | Upper | no no | 225 W. | 18 l / min | 72 M. | 110 mm | 1459 rub (cord 10 m) | |
| Patriot VP-10B (USA / China) | Upper | no no | 250 W. | 18 l / min | 60 M. | 98 M. | 7 M. | 1760 rub (cable length 10 m) |
| Belamin BV012 (Russia / China) | Lower | no no | 300 W. | 16.6 l / min | 70 M. | 100 mm | 3m | 2110 rub (cord 10 m) |
| Malysh-M 1514 poplar | Upper | no Yes | 250 W. | 25 l / min | 60 M. | 98 mm | 3m | 2771 rub (metal, cord 40 m) |
| NVT-210/10 caliber (Russia / China) | Upper | no no | 210 W. | 12 l / min | 40 M. | 78 M. | 10 M. | 1099 rub (cord 10 m) |
| Bison Master Spring NPV-240-10 | Upper | no no | 240 W. | 24 l / min | 60 M. | 100 meters | 3m | 1869 rub (cord 10 m) |
| QUATTRO ELEMENTI ACQUATICO 250 | Upper | no no | 250 W. | 17.5 l / min | 75 M. | 100 meters | 2 M. | 2715 rub (cord 10 m) |
| Aquarius-3 (Lepse) | Upper | No / is | 265 W. | 26 l / min | 40 M. | 98 mm | 1900 rub (cord 10 m) | |
| Kid 25 m (Kursk) | Lower | well no | 250 W. | 7.1 l / min | 40 M. | 1920 rub (cord 25 m) |
Each type of pumps is represented with different electrical cord long and the price changes (the longer the cord, the more expensive). You can also find varieties with dry-run protection, but you can make it yourself (see below).
Installation in a well or well
Submersible toddler pump suspended on a synthetic cable. Metal cable or wire quickly destroyed from vibration. Their use is possible if at the bottom - at least 2 meters - the synthetic cable is tied. To secure it in the top of the case there are eyeles. They do the end of the cable and is carefully fixed. The node is located at no lower than 10 cm from the pump housing - so that it does not sleep inside. Cropped edges are melted so that the cable does not break through.Cable clings for a special eye
Connecting hoses and pipes
At the outlet nozzle of the pump, the feed hose is put on. Its inner diameter should be slightly smaller (for a couple of millimeters) diameter of the nozzle. Too narrow hose creates an additional load, because of which the unit faster burns out.
The installation of flexible rubber or polymer hoses, as well as plastic or metal pipes of a suitable diameter is allowed. When using pipes, the pump to them is connected by a piece of flexible hose with a length of at least 2 meters.
Scheme of the installation of the submersible vibration pump
The hose on the nozzle is fixed with a metal clamp. Usually there is a problem: the hose scores from constant vibrations. So that this does not happen, the outer surface of the nozzle can be treated with a file, giving it additional roughness. You can also twist the groove under the claw, but do not get drunk hard. It is better to use a stainless steel claw with notches - it gives additional stiffness to the mount.
The clamp is better to take such
Preparation and descent
The installed hose, the cable and the electrocabool are tightened together by installing the tugs. The first is placed at a distance of 25-30 cm from the case, all the others with a step of 1-2 meters. Trets can be made from sticky tape, plastic clamps, slices of synthetic twine, etc. The use of metal wires or clamps is prohibited - they do with vibrations in vibration cord, hose or twine itself.
The shit of the well or well is set by the crossbar for which the cable will be mounted. The second option is a hook on the side wall.
The prepared pump gently descends to the desired depth. Here, too, questions arise: at what depth to install the submersible pump kid. The answer is twofold. First, from the water mirror to the top of the housing, the distance should be no more than the depth of the immersion of this model. For the "baby" firms, firms are 3 meters, for the Patriot unit - 10 meters. Secondly, to the bottom of the well or well there must be at least meter. This is in order to not hard to bumble water.
Bind plastic, kapron cords, sticky ribbon, but not metal (even in the shell)
If the submersible pump, the baby is installed in the well, it should not touch the walls. When installing in a well, a rubber spring ring is put on the housing.
Having lowered the pump to the required depth, the cable is fixed on the crossbar. Please note: the whole weight should be on the cable, not on the hose and not on the cable. To do this, when fastening the twine is stretched, and the cord and the hose weaken slightly.
Installation in a shallow well
With a small depth of the well, when the cable length is less than 5 meters, for neutralization oscillations, the cable is suspended to the crossbar through the spring gasket. The best option is a piece of thick rubber, which can withstand the load (weight and vibration). The use of springs is undesirable.
Fastening options for submersible vibration pumps with top and bottom water fence
Installation in the river, pond, lake (horizontal)
Operate the submersible pump kid can be in a horizontal position. Its preparation is similar - to wear a hose, copp all the screeds. Only then the case must be wrapped with a rubber sheet with a thickness of 1-3 mm.
Vertical installation option in open reservoir
After the pump is lowered under water, it can be turned on and operated. It does not require any additional events (fills and lubricants). It is cooled with the help of pumpable water, it is because it is precisely the inclusion without water is extremely bad on it: the motor overheats and can overdo it.
Features of operation
In some models of submersible vibration pumps for wells there are protection against overheating. This is a very useful feature that prevents the motor brave. With long-term operation or with impairment conditions, the built-in thermostat (overheating protection) opens the power supply circuit, turning off the pump. After some time, the relay comes in its original state and the work is resumed.
Another protective rings
If your pump disconnected overheating, it is desirable to immediately find out the cause. Disabling may be caused by the absence of water, increased voltage. If so, you only need to run the equipment when everything comes to normal. Another possible reason - the suction pipe has been clogged. With this you can fight only delivering a pump, disassembled and reading it that on the warranty period to do contraindicated. Although, if you have been hammered by the pump, you have already violated the rules of operation - it is suitable for pumping only pure water.
Dry Protection
Since many of the kids models are lowered below three meters from the water mirror, it is impossible at a small debate that the water will end, and the pump will continue to work and result in the perch. To avoid this situation, you can set the water level sensor. This is a float sensor, which is called a "frog". It works very simple:
Float water level sensor
- When it raises up, contacts are closed, food is served;
- When the water level is lowered, the float is lowered, the contacts in the sensor are blocked by breaking the supply circuit;
- Water is gradually recruited, the float rises above, at a certain level, the contacts are closed again, the pump is included in the work.
It is worth such a sensor - less than 1 tr., It is simply installed - in the rupture of the feed cable, but the benefit from it is large.
Working with hydroaccumulator
In general, vibration submersible pumps are not designed to work in a bundle with a hydroaccumulator. They cannot create enough high pressure. But ... under certain conditions they work. Assembly scheme Standard: Pump, pressure switch, pressure gauge, hydroaccumulator, all this is assembled through a positive fitting. For normal operation at the end of the hose immersed in the water, the check valve is installed (so that the water does not flow back into the well). Another condition - the hydroaccumulator must be a significant container (100 or 150 liters).
Private House Water Supply Scheme with Submersible Babe Vibration Pump
Collecting this scheme is required to adjust the pressure relay. It is asked the less, the better, otherwise the baby does not have enough power. But even with a slight pressure, everything will work for a couple of years, but rather - a year and a half.
What to do to worked longer
The toddler type pumps are very few, but also serve for a short time - about 2-3 years. In their production, inexpensive materials are used - to reduce cost. If immediately after the purchase, there are some activities, as well as carry out regular "technical inspections", you can significantly extend the service life. So what can be done:
- Screws, fastening the housing immediately replace to longer, add them to lock nuts. If this is not done, the bolts are cleared and break the rod.
- Once a month, inspect the pump, when pumping the polluted water, disassemble and rinse.
- When operating with a hydroaccumulator, set minimum pressure.
- Install protection from dry stroke.
- Serve voltage through the stabilizer.
Some of the events are costly. For example, the stabilizer is also approximately or even more of this pump, but it can be used with other types, and they all better work with stable voltage. But change the bolts - this is the key point that you want to execute.
Article on the topic: Entrance Gate: Types and characteristics