In almost every family there is an old furniture that was inherited, but not always this furniture has an acceptable view. The upholstery is simple enough. Then the favorite grandmothers chairs and chairs will get a second life and will play with new paints.
Instead of buying new chairs, you can make upholstery of old: shabby seats replace new, saving money.
Stool tightness with soft seat
To do this, you will need:
- dense tape;
- lining fabric;
- upholstery fabric;
- filler (batting, sintepon, coconut fiber);
- furniture foam;
- construction stapler;
- Hammer and nails.
Cut the chairs on your own not so difficult if you follow the technology and know the assembly sequence. It happens when not only the casing, but also the internal contents require replacement. First of all, you need to remove the seat, pull out old nails with a nail, remove the upholstery and filler. You should have only a wooden frame from the seat.
For the upholstery of the chair, the main tool serves a furniture stapler.
Now you need to attach along the bottom (in the form of a grid) a dense tape, which is used for furniture upholstery. One end of the ribbon to quit 3 nails, the second end wrap onto a wooden bar and tension. From the opposite side, fasten the tape with the help of nails, and then cut it out, the end is adjusted and secure the stapler. The distance between the stripes should be about 5 cm. The chair's seat is usually nailed for 2-3 tapes on each side, while binding them between themselves in the form of a grid. Instead of nails, it is possible to use the stapler - in this case, the brackets are located in 2 rows, at a short distance from each other. For this purpose, it is better to take a bracket of 8 mm.
Article on the topic: how to remove the lock (castle larva) with interroom doors
After that, take the lining fabric and fix it with a stapler throughout the perimeter of a wooden frame. Next lace a layer of filler. It can be batting, coconut fiber or syntheps. After cutting a piece of foam rubber in such a way that it turns out to be more seats for 2-3 cm. First, it is fixed with the brackets in the center of each side, then the sides are shot. The corners are laid in the last place, while the ends are assembled into small folds. During work, it is necessary to ensure that the foam rubber does not turn, otherwise the upholstery will turn out to be uneven and will acquire an inaccurative appearance.
To drag the chair, you must first strengthen the frame, and then remove the streaming tissue stream.
It remains only to cover the seat with a cloth. Spread the matter on the table, put the seat on top (foam down), shoot 3 brackets in the center of each side. Try to pull the fabric evenly so that you have no distortion, otherwise it will affect the appearance of the product. At the corners, lay beautiful folds, shoot them with a stapler, cut everything too much. Separate your ends and secure them in the same way, and then install the seat on the chair.
Cut the seat chairs with your own hands more difficult if there are springs in the upholstery. Many furniture masters do not recommend replacing them into less durable foam rubber. First of all, you must carefully disassemble the contents. As a rule, the springs are already interconnected. Then you can only check the bunch of the fortress. If some threads are lost over time, they need to be replaced. After you have knitted tapes and lining, install a bunch of springs on it, sewing each bottom (multiple stitches from all sides). On top of the design, fasten the dense lining fabric and just as the springs to it. Next follows a layer of batting or syntheps, after which the seat is frown and installed it on the chair.
Article on the topic: Malfunctions of pumping stations and their elimination
Tightboard chair with a solid seat
To do this, you will need:
- thick furniture foam;
- dense fabric;
- construction stapler;
- braid;
- Adhesive pistol.
Chair tight circuit.
Cut the chair with a solid seat is simple enough: even a person who does not have anything to do with the furniture business can easily cope with this. At first it is necessary to cut the foam rubber, it must completely repeat the size of the seat. Coloring fabric is not necessary, since it is much easier to work with a cut, which is 15-20 cm more laid.
The foam rubber is laid on the chair seat and cover it with a cloth. First tar (along the side) each side in the center, then on the sides. After that, the corners are arranged: the fabric is collected in small folds and fix the brackets. It is important to monitor that the brackets are clearly over the line. Next cuts off the matter, retreating from the mount by about 5-7 mm.
It remains only to glue a braid that will hide a bracket. This is the easiest way to do with the adhesive gun - work although the light, but requiring maximum attention and accuracy. In the same way, the upholstery is carried out, but in this case the upholstery tissue is not shot on the side, but on the reverse side of the seat. Therefore, it is not necessary to decorate the seam braid.
How to replace the upholstery on the couch?
To replace the upholstery, you will need:
The coupling of the chair is made using a construction stapler, upholstery fabric and hammer with nails.
- upholstery fabric;
- construction stapler;
- Hammer and nails.
Update the upholstery on the old chair is possible on its own. First of all, it is necessary to gently dismantle the former upholstery.
It is important to remember exactly where the fabric was attached, and even better to take a picture of it.
Use the old upholstery as a pattern, with a plot, add a transpass of 1-2 cm on each side.
First pull the armrests. In order for the tissue to be pulled easily, in its edge sewing a rigid braid (from the back side). If there is no in the farm, you can use a strip of dense cardboard (it is shot in the stapler). The upholstery repeat the same way as it was previously done.
Article on the topic: Purple wallpapers in the bedroom interior: Useful rules (photo)
After that, it is embarked on a fairly important process, tightness of the back. There should be no distortion and folds. In order for the fabric to lay exactly, it is necessary to build the following device: Take the DVP, cut off the long strip of 2-3 cm wide, learn wallpaper nails in it (at a distance of 1-2 cm), after which the bottom of the bottom of the upholstery tissue is accessed. By doing so, you can easily stretch the fabric and secure it on the bottom of the chair. For this purpose, use deep staples 0.8 or 10 mm.
After the back and armrests are pulled, proceed to sewing the seat cover. Based on the old case. If the lightning is well preserved, then it is not necessary to replace it with a new one. The bottom of the chair is tightened in the same way as the back.
Using the tips outlined above, you can easily update not only a chair or stool, but also an old chair. Dare, and you will succeed!