Replacing the cuff in the washing machine with front-loading may be required for various reasons, but for this problem it is not necessary to call the wizard. You can change the elastic band at home without any special tools in any typewriter, Whether it is a model from indesit, samsung, lg or another brand. The procedure will take about 30-60 minutes and save your funds if you figure it out exactly how the cuff replacement is performed.
Causes of damage
Replacing the cuff is most often due to the appearance of gaps or cracks on the seal, driving water during washing. As a result of the formation of such damage, the owner of the typewriter will see under hatch of water, and inspected the cuff itself, removes the cracks or breaks that can have different sizes. The causes of this situation are such factors:
- Natural wear of the sealer. In the process of operation, the cuff driver is constantly jencing the drum and linen. It is heated when washing, and then cooled. In addition, it affects detergents. Over the years, this leads to fragility and fragility of rubber.
- Poor-quality washing powder. Under the influence of a cheap powder and detergents with dubious quality, the cuff rubber begins to collapse, so the savings on the powder leads to expenses to replace the seal.
- Excess detergent dosage. When using a powder or liquid agent in an unnecessary amount, the structure of the sealing gum may also be damaged, due to which the cuff will have to be changed.
- Details of clothing that can damage the seal. Such elements can perform metal and plastic fittings. In addition, screws, nails and other items that can cause cuff breaks can get into the typewriter.
Over time, if you do not clean the sealing cuff, it can start mold on it. Therefore, it is necessary to periodically clean the washing machine. How to do it, you can see in the next video.
Article on the topic: Standard Width and Roll Length Wallpaper
How to remove?
- Prepare a flat screwdriver to work, and if your typewriter is old, then the rounds. Also, do not forget to de-energize the machine and turn it off from the water pipe.
- First remove the door with the machine, as well as the hatch lock. Your main actions for disconnecting the cuff will be removed clamps used for fastening the gum to the front wall of the device and to the tank body.
- Gently unscrew the front edge of the cuff, then loosen and remove the first clamp. If this part is plastic, it is fastened with latches, and the metal clamp is fixed with a screw or spring, to remove that you want to use a screwdriver. The screw should be unscrewed, and the spring is to delay a bit and weaken. Finding a screwdriver clamp, it can be removed. If the machine is an old model, in the design of the clamps there are no adjusting bolts or latches, and to remove such clamps, you will have to work the rounds.
- The following your action is careful disconnecting the front of the sealing gum. It is kept in the typewriter due to its shape and its own tension.
- After that, you need to proceed to disconnect the second clamp. Sometimes for this task you need to remove the case cover of the machine. Using a screwdriver, unscrew the bolt of the clamp or just shift it. After that, the cuff can be removed from the device.
How to replace?
First of all, you should purchase a sealing gum you need. Since the cuffs from other models can not approach yours, even if they are the same, be sure to tell the seller during the purchase of the seal model of the washing machine to which you are going to install the cuff. Only making sure that the acquired cuff is exactly the same as your damaged seal, you can proceed to a replacement that includes such actions.:
- Clean the edge of the tank from contamination (salts, powder and others). For this task you need a warm soap solution. Removing all the dirt, do not flush the film formed from the treatment with soap solution, as it will help in installing a new cuff.
- We establish a sealing gum on the tank. Note that it will not be too easy to do this with a new rubber band. Attach the top of the sealer to the Baku (its top edge) so that the tags coincide, then pull the cuff with the help of two thumbs. For this, your fingers should slide from the center to the sides. In this case, at the bottom of the cuff will not slip, but shook on the edge entirely.
- Check whether the cuff is installed correctly. Water drain holes should be located strictly at the center, and the tongue that is available in most gum should be at the top. In addition, after installing a gum should not form any gaps, since due to a loose fit, leaks are possible.
- Tensioning the inner clamp. You need to act depending on the attachment of the clamp. If its fixation is provided with a stretched spring, you need to wear a spring part of the clamp on a screwdriver (if you did not remove the front wall, then shook the screwdriver into the lock hole). So you can freely stretch the spring and dress the clamp in its place. In the case of a stretch with a screw, you should simply unscrew the screw, put the clamp in its place, and then tighten the screw to the required effort. It is even easier to fasten the plastic clamp, held by the latches. If your model is a wiretube wiret, carefully tighten its ends with the help of the roundheads, and then remove the knot into the existing deepening of the cuff.
- We put on a sealing gum on the front wall and stretch the second clamp. All manipulations with the second clamp are carried out in the same way as with the inner, depending on the features of its attachment.
- Check the tightness of the mounted cuff. To do this, include any short wash program, without loading underwear, and make sure that the water does not flow from the bottom of the cuff.
Article on the topic: What looked curtains with roses in the interior
It also happens that the front panel on the washing machine is not removed. It is not entirely convenient to replace the cuff. There is a way out of this situation and in the next video describe in detail and tell how to replace the sealing cuff on such washing machines.
Advice
To prevent the appearance of damage to the cuff due to metal locks and other fittings on clothing, use for washing things with plastic or metal elements special bags. In the absence of a bag, turn the locks inside the clothes.
In addition, it is important to always inspect the pockets of things before loading into the washing machine, in order to prevent any items that are capable of cutting into the device that can cut the rubber seal.