Replacement bearing in the washing machine with their own hands

Anonim

Replacement bearing in the washing machine with their own hands

Bearing is an important element of the device of the washing machine. It is a metal puck, which serves as a support for the rotation shaft of the drum. The bearing helps evenly distribute the burden on the drum, so its health is very important for stable operation of the device. Bearing wear largely affects the quality of washing, so it is very important to notice the signs of breakage on time, and replace the part.

Replacement bearing in the washing machine with their own hands

A characteristic signal saying that the bearing is faulty, is an extraneous noise, published by a washing machine when working. As soon as you heard an unusual buzz or tapping, you need to immediately establish the cause. If the case is in the bearing, the broken spare part will have to be replaced.

How to do this, without harming the washing machine, read in our current article.

Instruments

To get to the bearing, the washer needs to be almost completely disassembled.

To do this, you may need the following work tools:

  • Screwdriver Set;
  • chisel;
  • a hammer:
  • hacksaw;
  • Pliers and nippers;
  • Key set;
  • set of hexagons;
  • silicone sealant.

Do not forget also about new spare parts - Bearing and seals.

Replacement bearing in the washing machine with their own hands

Instructions for removal

  • Turn off the washing machine from the electrical outlet, disconnect the hoses from water and sewer pipes.
  • Move the unit from the walls, so that it has free access from all sides.
  • Behind the washing machine, we find two coils in the upper part and unscrew them. Remove the lid.
  • Disconnect the feeder of the washing powder.
  • We unscrew the bolt, which is under the feeder.
  • Remove the front panel located at the bottom of the device.
  • We find two bolts under the panel, unscrew them.
  • Alternately remove the two clamps that fix the rubber cuff on the hatch.
  • We are tightened from the edge of the hatch itself.
  • Press the device that provides the hatch lock.
  • Remove the front panel of the washing machine.
  • Remove the rear panel of the washing machine.
  • Remove from pulley strap.
  • Disconnect the wires leading to the Tan, pre-photographed their location.
  • Disconnect the nozzle connecting the pump with the tank.
  • We unscrew the two bolts on which the engine is recorded.
  • Remove shock absorbers and springs on which the tank is holding.
  • Carefully pull out the tank itself.

Article on the topic: how to choose the right color and style curtains for the hall

Replacement bearing in the washing machine with their own hands

Replacement bearing in the washing machine with their own hands

How to replace the bearing?

Pulling out the tank, define it look. The tanks of washing machines are detachable and not detachable. The plug-in tank consists of two halves interconnected by brackets or bolts. In this case, you just need to remove the fasteners. If the tank is solid, we cut it on the weld with a metal knife for metal.

Replacement bearing in the washing machine with their own hands

Next, act in this order:

  • We will disshinate the pulley (wheel) of the drum. We do it with the help of a suitable key or work with a hammer and chisel.
  • We overlook the pulley and gently remove it from the screw.
  • The same tools, trying not to damage the shaft, knock the drum from the hatch.
  • We find bearings on the inner and at the outer parts of the drum. Moving in a circle, knock out the wear bearing from the nest.
  • Clean the nest from pollution, processes it with a sealant or special lubrication.
  • We drive into the nest a new bearing and replace the glands.

Replacement bearing in the washing machine with their own hands

Replacement bearing in the washing machine with their own hands

Visually, the entire process of replacing the bearing, you can look in the following videos for some brands of washing machines.

Beko.

Samsung

Miele.

Siemens, Bosch.

Ardo.

Indesit.

Electrolux, Zanussi, AEG

Advice

  • If you decide not to seek help from a professional, and change the bearing yourself, we recommend that you free up for this all day, and better - all weekends. Disassembly and assembly of the washing machine - the case is quite time-consuming, especially for novice masters, so the errors can not be avoided.
  • Together with the bearing, be sure to change the glands, so these details wear out quite quickly. Before installing a new detail, read the place of installation well.
  • It is advisable to first extract the old bearing, and then buy a new one, similar. When buying, pay attention to the marking: it must match, otherwise the item is not suitable, and the money will be wondered.

Replacement bearing in the washing machine with their own hands

Replacement bearing in the washing machine with their own hands

Read more