Electrocosa - What is it?
The same device is different manufacturers of gardening inventory can be called differently - someone's trimmer, and someone's electrocosa. But in initially the trimmer was called such a device that mowed the grass with the help of a rotating fishing line. And now you can install a coil with a fishing line almost every such tool, but this does not mean that they are all belong to trimmers.
It is believed that the trimmer can be called rechargeable or electrical mowers, in which the electric motor is located below. But the tool in which the electric motor is located on top, is called an electrical oblique. Depending on the design, equipment and power, electrical braids can perform a wide variety of functions - from trimming grass on the lawn to clearing the bushes of shrubs on large areas of land.
Models of electrical spacecraft
In electrical models of Kos, in addition to simplicity in maintenance and low prices, there are other benefits. When working with such devices, there are no harmful exhausts, and the noise level during operation is much lower than that of gasoline models. But among their disadvantages, you can note the presence of a wire that interferes with work, as well as the fact that they necessarily need an electrical outlet for work. Also, do not forget that you can get a blow to an electric shock, if the wire isolation is damaged. It is for this reason that it is forbidden to work with an electrocosa during the fallout of any precipitation.Article on the topic: Principle of operation and mechanism of the management of blinds
Models with battery
Now in the market you can find models of electrocos working on batteries. There are such braids are much more expensive than ordinary, but at the same time they are very ergonomic and comfortable. The main disadvantage of such electrocos is the limited service life of their batteries, which in turn does not allow the use of this device for a long time without recharging.
Engine and rod design
Rod electrocouples is one of its main components. The rods can be different and differ in several signs: whole or detachable rods, as well as curved or straight rods. Low most common light braids are most often equipped with a curved barbell. Such braids are intended to perform small amounts of work. The bending of the rods is necessary so that the fishing (cutting element) moves parallel to the surface of the Earth. More powerful electrocos, with the help of which thin trunks of trees and shrubs are cut, are always equipped with a straight barbell. Such electrocos have quite large sizes and have a lot of weight.
Shape of the handle
The handle is a distinctive feature of almost any electrical spit. For example, compact D-or J-shaped handles are most often installed on light models. In the place where the handle is articulated with a barbell, vibration-proof elements are almost always located.
Such models are conveniently used in the case when the angle of the pouch must often be changed, but they are not suitable for large volumes of work, as they have a very strong vibration, which does not save even vibration insulation. Most often, such models are used in hard-to-reach places where the usual lawn mower is difficult to penetrate, or in areas having a complex relief.
For work on large in size, it is recommended to use a powerful electrocos, which is equipped with a metal handle of the T-shaped species, which is very similar to the steering wheel from the bike. With the help of comfortable and wide handles, the electrocos can be moved horizontally accurately and easily. The position of the handle can be adjusted - tilt in any direction or move, for which it is only possible to weaken the clamp. There are quite a large weight in such electrocos, so a suspension system is needed for a long and effective work with it. Most often, an ordinary shoulder belt is used as such a system.
Article on the topic: High-quality laminate laying with their own hands on Faneru
Equipment of electrical braids
The coil with a fishing line is probably the most common snap-in for electric braids. Depending on the power of a particular device, the thickness of the fishing line is also selected. Manufacturers always indicate the instruction to the allowable diameter of the fishing line, which can be applied. Do not neglect these recommendations and use a fishing line with other parameters. If you set the line, the diameter of which will be more recommended, the engine may not have enough power to spin it to the desired number of revolutions, and in the event that you install a smaller diameter line, the risk of failure of the electric motor will appear, since the engine speed from - The short load can become very high and it will just burn.
The fishing line, as a cutting element, has one essential advantage - it is very safe. The fishing line can be very good to mock grass and ride all the solid obstacles. Therefore, it is necessary to cut the grass in the walls and fences only as a fishing line, and use plastic knives for these purposes only in some cases.
But to cope with the dried bungyan or shrub is not at least the largest fishing line, so in this case it is necessary to use knives or cutters, which, depending on the purpose, can have a variety of dimensions and shapes. For example, special discs with short teeth are well suited to cut thin trees, you can use long narrow knives for cutting a shrub, and in order to mow thick rigid grass, the best option will be steel cutting mills, the number of teeth of which is equal 4, 8 or more.
That is why, before choosing an electrocos, it is necessary to clearly decide on the front of the works that you plan to perform with this tool. After that, it is recommended to carefully study the instructions and find out whether the technical characteristics of the model you have chosen meet all your requirements.
Article on the topic: Protection against electric shock