Interior doors are not luxury today, but a very important and necessary part of the apartment interior. Properly selected design and sizes of many, many years will please you and those around them. Installing the door is both a simple and very difficult task. Especially if you have never done this. The first to install the door is better to the masters, and you are observed for the occurring process. But what should I do if your interior door began to creak or see? Possible cause is the door hinges.
Overhead hinges require a neat installation, since it depends on the normal door opening.
How to install loops on interroom doors?
In order to install chains on the door, you will need:
- pencil;
- loops;
- Construction corner;
- cutter (for loops of butterflies is not needed);
- screws, screws of the desired size and diameter (often come in a set with hinges);
- kerner;
- drill on metal of the desired diameter (just in case; basically take the drill with a diameter of 2 mm);
- electric drill or perforator;
- Forster drill with diameters of 35 mm and 26 mm (depending on the size of the loops).
Loop installation diagram.
The next step is to choose the type of loops, material manufacturing material, their quantity, and so on. As for the type of loops, there are three of them: overhead (H), mortise (B) and oiled (explosive).
Most often covered loops. The prevalence of card canopies lies in their sharedness, convenience in the installation, ease of product design. Production material is either brass or steel. Types of overhead suspended parts are several: loops Butterfly, double-sided, with two ordinary plates.
How to install butterfly loops?
Below are step-by-step instructions for installing butterfly loops. Decide with the placement of the door in space. What is the best and more convenient for you to open the door design: to the left or right, inside or from ourselves? To do not slip the doors, put something from a steady material under them. For example, stretch film, thin rubber sheet and so on. The loops must match the weight of the door. Heavy structures are attached to the suspensions with five gaps under the self-tapping screw, lighter - by four.
Article on the topic: Original methods How to use curtains instead of doors
Before installing the loop, you need to make a markup correctly.
An important fact remains the fastening of the loops on the door so that it remains solid, does not sang and that the load on the loop was uniform. Basically, it takes a gap from below and on top of 20 cm. And an indent is made along the surface for placing a loop of 21-22 mm. If there is a third loop, it usually can be placed in the center or closer to the top. You can attach a loop to markup and circle them. You can also attach screws and make markup. Choose yourself. Of course, the best option is the one where the door surface damage is not provided.
Apply a pencil primary marking of the location of the loops on the canvas and on the door frame. When you are confident in the accuracy of measurements, hover them with Kerner. Try not to confuse the loop, the upper from the bottom or with the middle. When you make a markup, they must be placed with hinges to the front of the doors.
Required recommendations
Installation of loops directly on the door lies in the fact that it is necessary to attach a loop exactly to the induced markup. This will prevent the appearance of wood splits. After that, you can twist the screws from the kit. If you twist the suspension with screws, then Kerner will help you. Easy deepening will not allow the screws to "move" to the side.
A uniform location of the loops is measured using a construction corner.
For long exploitation of structures it is very important that the details data are on the same level. If they are loosely falling to the plane of the canvas or door box, we will establish uniformity with a laying or selection of loops with a small divorce.
Do the same procedures on the door frame. Secure the second part of the loop and connect the canvas with the box. All, the installation of overhead loops on interior doors is made. What kind of suspended items to install, choose only to you and anyone else. Butterfly overhead loops are considered the most comfortable, in this case, models. A small minus concerning the uniformity of the loop distribution on the surface can be easily minimized by lining. We hope that these tips of experienced specialists will help you at the right moment, because now you know how to install a loop.
Article on the topic: How to connect a shower cabin to the water supply with your own hands?