In each dwelling there is an entrance door. Door's covering with their own hands is used quite often, especially domestic owners. Cats and dogs with their claws can spoil the appearance of the doors. Scratched or crushed covering not only spoils the appearance, but also reduces the level of sound insulation and thermal insulation.
Sketchy images of upholstery drawings inlet doors.
Door Materials
Put entrance doors with different materials. The most common ones are:
- MDF panels;
- laminate;
- leatherette;
- vinylisco;
- array of wood;
- lining.
The laminate and MDF panels look beautifully, have a long service life. But it is possible to sow these materials only the surface of the doors inside the room. Outside, the trim may fail by the instability of the material to the rain, the snow, the wind and to the temperature differences.
The process of insulation of the entrance door, with the main sizes.
Dermatin and widespread vinyliques can be applied on the street. One should only remember that dermatin can be easily spoiled by an extraneous mechanical effect. This material is easily cleaned with a damp cloth and is relatively cheap.
Wooden array and lining belong to the most expensive sheathing options. But also serve these materials longer than everyone else with good care. The tree must be periodically painted, put off, varnish, polished.
Out of the doors dermatin
Tearing doors are made in this way:
- Removing the old sheathing and fittings.
- Preparation of a new trim set.
- Opening doors.
Before fastening the new trim, it should be removed from the doors of the accessories to which the locks, latches, handles, eyes. After that, the whole old sheathing with nails and screws is removed.
To install a new set of casing material, you may need:
- epoxy adhesive;
- leatherette;
- stapler;
- plywood;
- foam;
- scissors.
Article on the topic: How to fold napkins on the New Year's table
Door upholstery scheme.
The entire surface of the door should be covered with glue. A sheet of plywood is attached to the glue layer. Plywood is applied to the metal door frame. It is easily clogged with nails and brackets. From the Dermatin strip, about 10 cm wide and a length equal to the perimeter of the door, a roller filled with Vatin is made. This roller is fixed by the stapler to the door edges. The fabor is placed on the cloth with a margin of about 10 cm on each side. From above everything is closed by dermal. The material is attached first in the center, then on top and bottom. Dermatin needs to tighten well so that in the course of the operation of the doors he is not wound and not wrinkled.
The main work is made. It remains to install the handles and locks, embed the eye, decorate the surface of the door with special nails. The finished door may look like. Pattern options can be a lot. It depends on the aesthetic taste of the host. You can decorate the sheathed with thin flat flat cords from dermatin and nails and buttons with large hats.
Tree and plastic
The sheathing of doors with wooden or plastic materials is recommended by masters. These materials have sufficient strength and beauty. Wood is used dry, treated with antiseptic compositions to protect against fungi. Wood breed can be any. Details (lamella) are recommended to choose the minimum width. At mounting, they simply jerk and form a smooth surface. Boards can be installed horizontally or vertically, at an angle in different directions. The simplest option.Such a casing is an excellent insulation from noise, from winter jewelry. It has high strength. But periodically material requires treatment with varnishes, paints, antiseptics. Need fireproof wood processing. Plastic in this regard is less demanding.
Several useful tips
- To prevent drafts, the loops from the loops is closed with a strip of polyethylene, attaching it by the stationery buttons.
- On double doors, a vertical roller is installed on half with the door handle.
- From drafts, you can protect yourself using a rubber tape or tube that are nailed around the perimeter of the door to the jamb.
- If the entrance door opens out, then the vertical and top rollers on the inside are attached directly on the door frame.
- Fastening nails and brackets are located at a distance of 10 cm from each other.
- All materials are attached to the metal door with the "moment" glue. Another way is to attach a sheet of plywood to which the trimming material is nailed.
- Wooden parts before the trim should fly in an adaptation room for no less than a day.
- Stacking wooden lamellas It is recommended to start on the left side of the door canvase. The details of the finish nails are attached. The ends are processed by a grinding eye.
Door lining can be done with their own hands.
To do this, it is necessary to purchase material, which uses dermatin, artificial or genuine leather, wood, plastic, MDF and other species. A leaf foam rubber is used as insulation. The work itself takes little time, but the result for many years can please the eyes.
Article Artificial Stone Shell for Bathroom