The repair is very important to bring everything to a logical completion. For example, when plasterboard walls are erected, special attention should be paid to the process of shtlock. It seemed like - such a trifle, and requires approach and skill.
If you have never before put the putty on plasterboard, in this article you will find everything you need to learn this.
In order to achieve perfectly smooth walls, you need to make a lot of effort
Beginning of work
After the walls or partitions from drywall will be erected, you can proceed to surface processing and preparation for finishing work. To do this, you need to stock up tool and construction materials:Tool
- Drill with a "mixer" nozzle. Of course, it is possible to do without it, but the power tool is much more efficient to work, do not give up progressive "helpers".
- Capacity for mixing the solution. A common bucket is suitable if nothing more aesthetic is not at hand.
- Brush and spatula. The plasterboard joints are better to carry out a wide spatula, the minimum size is 100 mm, for large areas it is convenient to use 350-400 mm.
- Smallozing sandpaper or grinding net.
- Construction knife.
Note!
Many experts advise you to purchase a small spatula (30-40 mm), which is useful to apply putty on the self-tapping screw.
Materials
Now let's see what is necessary for the workflow:- Putty for jacks of plasterboard. She can also be called "for sealing seams."
- Ribbon for the reinforcement of the joints. You can use the usual greater tape.
- Finish plasterboard spacure.
Tip!
Take advantage of the finished mixture that is sold in buckets. The price for it is slightly higher, but the quality significantly exceeds all dry putty.
- Primer deep penetration.
It is all extremely necessary for our work, so it should not save on something. If you abandon any stage, you can pay for it in the future of early renovation.
Article on the topic: Inspiration of the day: Candle lanterns for decoration of the house and cottages (27 photos)
Preparatory work
The very first thing that is required is to clean the surface of the drywall from dust and spray solution.
- Take a spatula in my hands and holding it at an angle of 30 degrees, spend over the entire surface.
- In those places where it will cling, try to cut pollution carefully.
- If the spatula hooked behind the screw of the self-press, it means that it should be dried by 0.5-1 mm from the surface.
- Surface dust is removed slightly damp rag, carefully cleaning the joints of the plasterboard. Try not to wet the places where there is damage to the paper layer.
Now it is necessary to make a chamfer in the locations of the sheets of sheets, if not. To do this, use the usual building knife, which you cut the material at an angle of 45 degrees.
Do not pay attention to the smooth chamfer - this will not affect the quality of the applied putty
Important!
Do not try to make it too deep, enough 2-3 mm so that the solution is completely clipped.
But this is not all before, before putting the joints of the plasterboard joints, the surface must be processed by primer.
It is better to use a woolen roller to apply it, it is much better rubbing the primer into the surface than the brush.
- Using one of the proposed tools, the entire surface of the walls should be carefully soaked.
- Especially acute attention in those places where the screws and joints.
Now it remains to wait until the primer dries out, it may take several hours (see the packaging of the mixture).
The last stage in the preparatory work will be a sticker reinforcing tape. As we said, it is suitable for usual raner scotch. Look at the photo how the walls prepared for putting the putty should look like.
In this case, a special reinforcing grid is used to increase the adhesion of the finishing material.
The working process
So we got to the most important thing - the smear of the junction of plasterboard.
- The process of kneading putty begins . This procedure should be carried out in accordance with what the instructions on the package.
Do not try to invent anything new and use "Unknown Sources" - the putty of different manufacturers may differ not only in composition, but also a method of kneading.
For your information!
It is not necessary to cook at once a lot of mixtures, since its storage is short enough. Rate your strength and break the work area into several parts.
If the room is small, then you can do and alimile.
- Using a spatula, apply putty on the surface of drywall in small quantities.
Article on the topic: Unusual lamps and chandeliers do it yourself
Try not to leave on the surface of obvious irregularities that can cause problems at stripping
- Thoroughly smear the mixture so that nowhere remains unnecessary "irregularities".
- Little spatula. Mazing hats of screws.
- Wait until the putty dries, and with the help of a large spatula, remove all the tubercles.
Irregularities can be cleaned and using sandpaper
- Once again, we use the primer, process it all the new joints.
- Now the finish putty of the jacks of plasterboard begins. To do this, use a wide spatula. The putty layer should not exceed 1.5 mm thick.
Stripping the surface of the walls of the finish putty with a wide spatula
Articles on the topic:
- Sealing seams of drywall
- How to plastering plasterboard
- Sealing junctions of plasterboard
Specialist advice:
- Be sure to remove all the remnants of putty from the spatula. Before smoothing the mixture, be sure to moisten the tool in the water.
- For the convenience of applying, use a plastic pelvis, not a bucket.
- Do not disturb the method of preparation of the mixture, since a strongly liquid putty will dry longer, and too thick it will get a commercial.
Now you know how to put the joints of the drywall on their own, without referring to the services of the builders.
Conclusion
Agree, the process is pretty simple and does not require any particular effort. And yet, we suggest you watch the video: how to properly put the jokes of plasterboard with your own hands, on which you can visually familiarize yourself with all the processes described above. We wish you success in repair!