Today, collecting dolls made by your own hands, to order, as well as bought from limited release series or just popular. Store such a collection in a table box of course no one wants to anyone. Beauty should please the eye, be in mind, and not dust on the mezzanine. Therefore, real collectors have the need to make a stand for doll with their own hands. So that not only the collection surprised the originality, but the holder approached the favorite for all one hundred.
Possible materials
The doll stand must meet the following requirements, regardless of the materials for its manufacture:
- stability so that it does not fall on the side of the weight of the doll;
- Easy, so as not to distract attention from the doll itself;
- accuracy;
- Convenience in operation.
Possible materials for the manufacture of supports:
- wood;
- wire;
- cardboard;
- newspaper tubes;
- gypsum;
- computer disk;
- Swim cover, etc.
Consider various ways to create supports on the example of various materials.
Natural material
It will be about making a wooden stand for dolls. The material is the most environmentally friendly, but also the most difficult for beginners, and for masters without certain equipment. But, on the other hand, the wooden foundation can always be made to order or buy ready. For example, you can use a wooden platband or a coat for hot wood as a stand.
If there is an opportunity to make the basis for the manufacture of a wooden stand, then for this you need to take a flat bar of suitable size and weight. If there is a need, you need to cut out of it the necessary form base with a jigsaw. Carefully pollute the workpiece from all sides.
Rates a little bit from the edge or in the center to drill a hole for a wooden rack. Place for the hole and its size depends on how the doll will be attached to this stand and which thickness is the rack. If you wish to paint the workpiece or smear the sketch. Then open lacquer.
Article on the topic: Popertol: Master class with photos of finished works and video
Master class on the manufacture of a wooden stand for doll tilde.
Required tools in the photo:
Materials:
- Chinese wand;
- Ready wooden stand;
- wire;
- silk thread;
- knitwear or fleece;
- PVA glue;
- Acrylic paint.
Drill in the center of the workpiece hole suitable in the thickness of the Chinese wand, to keep well at the base.
In the wand, drill holes (non-trip) from opposite sides at distances 0.5 cm and 1 cm below the edge.
Make a blank from the wire, as in the photo:
Insert one end of the wire into one hole, and the other on the opposite side to another. Milk the place of connection.
Remove the seat seat and try on a doll.
From the fabric cut the part suitable for the size of the wire seat:
Sew detail right on the design.
If desired, decorate, open lacquer.
Paper Stands
This type of support is made from cardboard (2 mm thick) or newspaper tubes. Consider how to make the base from these materials.
For standing from cardboard, you will need:
- cardboard;
- Office paper or napkin;
- PVA glue;
- glue moment;
- sandpaper;
- acrylic paints;
- acrylic lacquer.
Depending on the desired thickness and the size of the stand, cut 6-10 pieces of cardboard. From pieces to cut the same circles.
Glue the mug glue the moment and put under the press for an hour. Embrete paper to process all irregularities on the sides.
The workpiece is punctured with mint office paper and dry in the oven. Optionally, paint and open lacquer. Make a hole for the holder.
The base of newspaper tubes. Prepare newspaper tubes. To do this, the newspaper page is cut into 4 bands. To start winding the newspaper from the corner on the knit. If the needker is closed by a newspaper, to move it away and continue to wind. When the newspaper is over, the tip is glued with PVA glue.
Take the first tube and wind it on the future rack. When the first stick is over, the rack can be removed. Tubes cheat so much so that the base diameter is sufficient for a stable stand.
Article on the topic: Children's rug crochet "Dog with heart"
Make several such discs, but each little less than the previous one.
Collect stand on the rack. To do this, each new disk is good to glued to the previous one.
The resulting pyramid was decorated at will.
Construction material
Consider on this master class, how to make a stand for dolls from plaster. Basic materials - gypsum, thick wire, metal tube.
Take a wire in length 3 times the height of the stand. Travel in half, form a ring for a rack, and then the holder in the size of the doll. Wire ends pass through a metal tube.
For the manufacture of the base, choose any unnecessary plastic mold. Gypsum is diluted in the desired proportion (indicated on the package) and pour into the mold. Insert the rack, leave to dry at room temperature. After a few hours, get out of the form, but leave for some time to bother. On wet gypsum glue does not hold, as well as the base can be easily damaged.
Decorate at your discretion. You can paint with paints, cover with cloth or corrugated paper.
Such holders are often used for Barbie dolls, Monster High.
Disk stand - master class on video:
Video on the topic
A few more video ideas: