Wooden doors gradually leave our everyday life, giving way to beautiful, durable metallic. But in the old houses of Stalin or Brezhnev building, double wooden doors are still found, frown from inside dermatin (dermatin) and preserved clapboard with clapboard from the outside.
The process of plating
What is the good upholstery doors Dermantine?
Wooden interior doors perform one function - the separation of space, and the inlet exterior is several. In addition to separating from the street, they protect the room from cold, isolate from external noise and odors, therefore, the requirements for them above. Upholstery enhances the functions of the entrance doors, protects them from adverse external factors, such as rain, snow and wind, creates an attractive appearance.
To achieve the desired effect, the upholstery material must respond to the tastes of the owner and comply with the following requirements and be:
- strong enough
- moistureproof
- elastic, slightly stretching
- Do not harde and not crack at low temperatures.
Modern materials are mostly high-quality, meet most of the requirements, but experienced joiners recommend the leatherette produced by India, made on the basis of synthetic tissue.
Choose one of three materials as a lining:
- batting,
- polyurethane foam,
- Sintepon.
Each of them has its own characteristics, positive and negative properties, but most people preference are preferred to polyurethane or, simply speaking, foam rubber. It contains a lot of emptiness filled with air, has a low thermal conductivity and helps the design well keep warm. Another important property is the ability to easily shrink and occupy very little space in a compressed state, which is very convenient when stroking eyes and pens. The foam rubber does not create hard rollers around them.
Consider detailed instructions with the photo, how do your own hands, to climb the inlet wooden door Dermantine.
- We remove the cloth with loops, put for convenience on the support of two or four stools.
- We free the entire surface to the wooden shield from the handles, eyes, castles, old upholstery.
- We measure the length and width of the door leaf and cut out of the dermantina flap of a similar size with a 10 cm in each side.
- Additionally, for sealing the doorway, the creation of the best thermal insulation and sound insulation, we will make rollers with each of the sides. To do this, cut off one strip equal to the door length, and two strips equal to its width. Each width - 14-15 cm.
Article on the topic: Ideas for the hallway with your own hands: Registration Arch, rug, cabinet
- We apply a strip of dermantine onto the wooden surface of the front side, involving up, shift the duck and fix the nails or furniture stapler one edge to the edge of the door. So do with all three strips that create a roller on top, from below and from the free side facing the Oblopault. The side that will hang on the loop, the roller will not have.
- We have left hanging flap for three sides of the product. They put the insulation sufficient to create a thickness roller closer to the inner edge, bend, gently convert and gently across the perimeter, as in the photo. Rollers are ready.
- Next, we cut a piece of the insulation of a suitable value, put on top and straighten.
- On top of the insulation, we put the pattern of Dermantine, clamor the edge and fix decorative nails with a wide hat first in the corners, and then throughout the perimeter in a step of 10 cm.
- The last stroke will be the waters of the handle, the door eye and the castle. We score decorative nails around them.
To climb the door from the inside, they do the same except rollers: they are cut out 4 pieces - two lengths in length and two - in the width of the door. The bottom is nailed to the doorway so that the threshold is closed, and the rest are tapped directly to the door frame.
Some owners seek to decorate the product with a new upholstery. To do this, use thin wire and the same nails.
- Location the arrangement of nails;
- They are not completely in line;
- stretching the wire between them;
- We score nails to the end.
New upholstery is ready.
MDF
Another way to give aesthetic appearance of the entrance door is the casing of its MDF. What is MDF slabs? They are created by pressing from very small wooden chips, and from above covered with a polyvinyl chloride film, which is also called antivandal.Article on the topic: Window windows: Benefits and disadvantages
Properties of MDF plates:
- High mechanical strength;
- resistance to moisture;
- pronounced sound insulation and thermal insulation;
- Not affected by fungus.
How to make a trim with your own hands?
The process requires a drill to drive holes on the doors and MDF plates. For facing work, MDF is 16 mm thick. They can be attached to the boards or dermantine upholstery. To improve the quality and reliability of the canvas, you can make a two-way trim.
Instructions for the door leaf trim:
- Place the cloth horizontally into two or four points of the support.
- Release the working surface from the fittings.
- Drilled around the perimeter of the oxo (the part that will close the frame), the holes with a diameter of 3 mm. The distance between them is 20 cm, as in the photo.
- The same is done with a cut-off mdf mdf of the desired size - drill holes with a diameter of 3 mm in a step of 20 cm.
- With the help of screws, tighten the lining with the door. Please note that their length should be a couple of millimeters shorter than the thickness of the resulting layer.
- Plunct the accessories and mount the door on the loop.
Here, in two ways, it is possible to drastically change the appearance and quality of the inlet wooden door, including from the inside. If something is incomprehensible - watch the video, how do it yourself shelter the door with MDF or Dermantine plates.