After you installed the door, you will definitely imagine a prayer picture before your gaze - a formed gap between the new door box and the doorway. But you should not despair that your opening looks not entirely attractive. The sealing of an ugly, damp site does not take you a lot of strength and money.
Finishing of the doorway
And to see how work is underway to improve the opening on the Internet on the video. Despite the fact that you do not have much experience, the finish with your own hands is real for any person, because the work is not very voluminous and will require you not so much experience as accuracy and creative approach.
With the help of door openings, the perception of the whole room occurs, and the perfect decoration of slopes, climbing the gap adds to your new door design.
Methods for performing slopes
The outer side of the door is finished by installer by installer. And on the inside - everything is terrible. Before your eyes are bare wall, bricks and a bunch of opportunities for the design of slopes.
The slope gives the doors a beautiful view, hides all the mounts and makes the whole design stable.
Therefore, after the box is installed, you need to choose the method of finishing, and they are not so much:
- Finishing with platbands and a good board;
- Plaster slopes;
- Printing material.
The division occurs at different ways to form a suggestion, and the material for cladding is not a problem. The most ideal option is to close the slopes with concrete followed by painting.
The decoration of slopes with the installation of finishing material on a special framework is beneficial when a decent volume of the solution is required for emptiness in the opening. Judging by the photo, this way the slope will be impeccable, even.
Article on the topic: How to make a coffee table with your own hands?
Features of finishing for different walls
The easiest way to close the openings in the panel houses. The walls from the panels are stronger than brick masonry and do not crumble at all, so the box is tightly installed in such an opening. Foam will be needed for closeing the opening of a bit.
Brick masonry is thicker than the concrete wall, it will turn around where.
Material for slopes can be any: suitable plasterboard, plastic and other leafy materials.
If you want the finish to look carefully, use PVC panels as finishing material, they are the most durable. Yes, and choose the door box in the color can be without problems.
Preparation for work
Whatever the way you choose, the preparatory work will be reduced to the collar of the film and the painted scotch of the entire design of the box to protect it from accidental damage. The decoration of the doorway involves preparatory work.
- It is necessarily removed all irregularities, roughness, which I can interfere with further work.
- It is necessary to clean the surface, accelerating it from dust and process to.
- If you are scheduled for a gasket in the opening of the cable, then you can start it, but not in the case of the construction of the frame.
Formation of separation by finishing material for the solution
- All finishing materials are attached to cement mortar or special glue.
- Screws are screwed to remove the level so that they are all on the hats. Since the sheath will be relying on these caps, take into account the thickness of the finishing canvas.
- The voids of the slopes are filled with a solution, and a reliable adhesive composition is selected. For better mounting, glue is applied on both surfaces: on the finish and surface of the slope.
- Then the finishing material is applied and a little attached. All work check the level.
- Final stage - fastening of platbands.
Installation of finishing on frame base
- Before starting work so that the surface does not pour it to drive it. For mounting the frame base, a tree rail or universal profile will be suitable. It is necessary to do everything so that the frame lay down tightly to the wall, if necessary, then equal to the wall.
- Fastening facing materials to the crate will be using plastic dowels and shock screws. Installation of the frame base starts with the installation of two ridges with jumpers on them. Installation of the trim for each material varies.
- Laminate stacked in different directions, but regardless of the direction all the elements are snapped. For stability, the panel design is additionally fixed.
- Plastic is laid, as well as the laminate coating, only to fix it additionally, because the plastic is not so durable.
Article on the topic: DIY for Valentine's Day do it yourself
MDF panels are the most beautiful, they can be chosen under the door of the door, and they will be attached to small cloves without hats, which are invisible on the surface of the panels. Corners, fasteners need to be closed with corners and platbands from MDF.
Plasterboard as the finishing material is fastened very easily on the self-tapping screw all over the perimeter. If there is a distance between the wall and finishing material, then it is filled with a solution, the joints are aligned with a special ribbon, the surface is sweeping, it is covered with wallpaper or painted.
Plastering
- Before scolding the doorway, you need to install beacons on the prepared soil surface, thanks to which it will be more convenient to align the surface. Specialists recommend using a gypsum solution for these purposes, it will climb instantly, it is not necessary to wait.
- Lights need to adjust in the direction of one plane. Then we proceed to filling the suction space with a solution of sand and cement. The solution is applied to the slope and equal in the lighthouses. If the solution is dry - proceed to the starting and finishing finish.
- The finishing putty solution after drying with the abrasive mesh is equal, after final drying is painted.
Whatever you choose a way to finish slopes, the main thing is that their appearance become an ornament for your door.