Elastic set of hooks for circular crochet and knitting needles

When creating a specific product, sometimes there is a need to perform an elastic hinge set. For example, when you start the sleeve not from the armor, but from the cuff. We will analyze the nuances in the performance of such work.

First method

Suitable for beginners of craftsmen and will allow you to score immediately facial loops, which will make it easier for further knitting. This method is used with a typing knitting needles for caps, socks, mittens, etc.

1. So far, without the spoke, take the tip of the thread in hand;

1. Wrap a thread around the index and middle fingers for half a circle. The last half has completed fingers. Wake up a loop between your fingers, as shown in the figure below;

1. Gently remove the workpiece from the fingers and tighten the loop;

1. Loading the face of the face, leaving the original on the needle. Knit a little loose;

1. We introduce a front door to a new loop. Slightly tighten it;

1. We repeat step 4 and 5 until you want the desired length.

Second attempt

Measure the end of the thread about one and a half times the width of the finished product, while, if necessary, dial a hinge for a circular knitting (for example, a sleeve, a neck, etc.). We put on a large and index finger thread. And the end that is short, should be closer to you. Following your fingers fix the continuation of the thread.

Set we carry out two spokes. It is necessary to bring the knitting needles under the thread between the fingers move towards yourself.

We will start the far thread for the neighbor. So we formed a loop around the thumb.

Here in this loop from the bottom up and told the needles.

Now right to left cling the loop on the index finger.

And they spend again through the loop on the big one.

The first two loops are ready, the following are dialing just. To start knitting, it is necessary to pull one of the spokes from the set.

Article on the topic: Horn of abundance do it yourself from newspaper tubes with photos and videos

Third way

Tubular set is performed by knitting for gum 2 × 2, 1 × 1. It will be necessary to prepare, except the base color thread, the thread of another color. It will be extra, then everything that will be fulfilled, we delete. What number of loops need to dial? And you will need half a half less than the size of the part. And add another loop.

For example, the main knitting should consist of 20 loops, which means that we recruit 10 loops, plus one, we get eleven loops in the initial set.

In the right hand placing a free end. The thread that goes from the tangler, placing in the left hand. Next, we supply it around a large and index finger.

We introduce the needle from the bottom up under the thread, which comes from the thumb, then we capture the moving from the index finger and form a loop.

It turns out a twisted loop.

We continue to gain the required amount of loops.

I turn the knitting and take the main thread. The first loop is knitted by the front loop the back wall, and so every loop on the left needle.

The next row, which is the second, is inserted by hinges, the third - facial, but already for the front wall.

This is how the interweaving auxiliary and basic filaments looks like.

The first loop on the spoke is in the invalid. Next, we select a mug of a loop, made by the primary color and throw on the left needle. Checking facial loop.

The next loop is preserved as an invalible. And again picked up a hinge alley, throwing it on the left knitting needles, check the facial. So check until the end of the row. We finish the wrong loop.

It is important to remember that the upper loops are always invalid. Those that we raise below - always facial. This is especially necessary to take into account when set for gum 2 × 2.

Remove the auxiliary thread.

Knit further according to the pattern.

More options

This option is suitable for those who are going to knit the product with a crochet. Let's knit with semi-brass with Nakud.

1. We recruit three air loops (c.), Make the Nakid, we introduce the hook in the first century;
2. Pick up the working thread and pull one loop;
3. We again select the working thread and insert three loops that are on the hook;
4. We carry out the nakid, we enter the hook for the left wall of the loop.

Article on the topic: How to make a volcano from plasticine with your own hands at home with video

We repeat the steps from the first one by the third until you score the required number of loops.

It is also done with a crochet, but the columns with Nakud.

1. We will connect four air hinges, perform the Caid and enter the hook in the first century;
2. Pick up the working thread and pull one loop;
3. We first select the working thread (R.N.) and pursue a loop;
4. Tweet R.N. and in two hinge receptions that are in pairs on the hook;
5. We do the Caid, we enter a hook for the left outer wall;
6. We repeat from the first to the fourth step until you check the required amount.

Here are some ways to recruit loops with knitting needles and crochet that we suggest to master. Perhaps some will be already familiar, and others in a novelty. We recommend to try all the offered, let it, if you may have a loop, however, when you are making a new product, one of the proposed options may be needed.

Video on the topic