If the front rail door is deprived of the castle, then, accordingly, it will lose its direct purpose - to protect the dwelling from foreign. But it happens that the castle itself fails for any reason, and then there is a need for independent intervention.
Castle design scheme.
In order to install the castle itself into the rail door, you just need to stock special tools. But I would like to immediately dwell on the fact that, despite the similarity in the installation processes of locks and on the wooden, and on the metal doors, some differences are still available.
The main difference between the entrance and interroom locks is its purpose. If in the first case the lock is purely formal, then in the second it is placed on it. That is why it is better to install the castle on the iron door, and two, and with different configurations and at a distance are not closer than 30 cm from each other. But for the castle to serve efficiently, the door itself should also be high quality.
Preparation of the necessary tool
Installation of the door constipation can be made only with the presence of the appropriate tool.
Tools for mounting lock: meter, pliers, screwdrivers, adjustable key.
It is impossible to do in this process without:
- Wood milling mill;
- screwdriver or screwdriver set;
- electric drills;
- hammer;
- feathery drill;
- typometer;
- measuring tape measure;
- Pencil and paper;
- self-tapping and screws;
- painting tape.
Montage of the Patch Castle
Such technology is suitable for both entrance doors, and for interroom.
Main steps:
Scheme of the device of the overhead lock.
- First of all, you need to check the lock of the lock, whether all the parts are available. Along with the product, instruction manual, as well as the installation rules for the rail door, with which it is also advisable to get acquainted. In the absence of any elements, you must immediately contact the place of purchase.
- After the documents and the equipment are checked, the paper is taken and the silhouette of the lock will be burned with a pencil on it. The drawing should store where the key well and the mounting holes will be located.
- In order to more accurately determine the dimensions of the key hole, the key guide is additionally applied to the sketch and the key guide is preloaded and is measured again so that in the case of which to correct the drawing.
- With the help of the tape, the resulting sketch is glued at the appropriate place of the door canvase. After that, all the marks are copied to it, which denote the lock well and the fixing of the castle itself. Since the installation will be made on the rail door, then you need to think about the welding of fastening pins.
- Next pins to the door attached the lock case with an already fitted key guide. At this point it is very important to control the combination of all grooves intended for the key.
- From the outside of the door canvase, you need to install a decorative lining for a key well.
- Next, with the help of the key, we put forward the riglels (two turns) and fasteners in the ratio of the shut-off bar. To make this work as clear as possible, the ends of the valves cover the paint, after which the rail door is covered, and the noted remains at the necessary places. You can navigate where to accurately drill holes for constipation.
- The next step will be the preparation of the above holes.
- After the furrows are ready, the retaliatory bar is attached and the lock is checked. If the riglies have a free move, the installation is made correctly. In the opposite case, it is necessary to conduct "configure". To do this, you may need to correct the location of the response or the need to smooth the edges using a file.
Article on the topic: How does the curtain from organza in the interior: let's see
Method of installation of a mortise lock in the rail door
Castle lock circuit on the door.
The order of work in this process is similar to the works in the previous one.
Required tools:
- Electric drill with metal nozzle;
- Bulgarian;
- Filter, feet;
- self-tapping screw;
- Construction roulette;
- screwdriver.
The location of the lock should be chosen taking into account the location of the rigid ribs. They can be diagonally and perpendicular to each other. Next, the installation of a mortise lock is carried out as follows:
- It is necessary to place the circuit of the lock case on the front side of the door, while the end plate should remain outside.
- An axial hole is poured with a grinder, intended for the location of the key mechanism. Next, it is necessary on the end plank, strictly in the center, cut the apertures that will serve for fasteners (self-samples).
- Make marking for future mounting of the door handle and the electric drill is cut out.
- The design of the lock is applied to the canvas of the iron door. Based on this, the place of the future location of the well for the key, drill it, observing the longitudinal form. After the work performed, the lock is inserted into the forms obtained and the accuracy of all holes is compared. On metal can form "burstles" that are sharpened with the help of the proper.
- After the accuracy of the holes is checked, the lock is attached by self-drawing using the fixation of the end plank.
- As the above was described above, it is necessary to place the location of the lock groove on the door box bar. After the paint marks denote them, they are also dried, and the edges are sharpened with a file, if Bulgarian was still used for this purpose. At this stage, you should know that the door can give shrinkage. Therefore, so that the lock is not jammed, the battered holes are made by 2-3 mm below.
- The last moment is to check the work. For this, the lock is open several times and closed by turning the key.
As it is clear from the instructions described above, the installation of the lock into the metal door is a rather light process, but at the same time requires accurate calculations and the presence of tools.
Article on the topic: Choose interior doors of the color Anegri: species and colors
Which lock to choose to install?
Cylinder lock diagram.
Before making installation of locking structures, it is necessary to know that the modern construction market offers two of their kind: Suwald and cylinder. Each of them has its own characteristics.
Cylinder lock model.
In everyday life is called an English lock. The system of such a model implies a secret mechanism that will only work if the work part is in motion only the right key. The lock consists of a larvae and core, which are located inside the standard case.
In this case, the convenience is that the larvae of such locks are made according to certain standards. Therefore, in the event of a breakdown there is no need to pick up a particular manufacturer. The form of the opening key has a large amount of recesses, cuts, and as an addition and side curly shape. This species ensures the complexity of the selection of pods.
Diagram of the device of the Suwal door lock.
The cylinder lock may be single or bilateral. Depending on this, it will have two or one well turnkey so that it was possible to open it.
When such a model is installed on the rail door, then in the case of its protrusion above the surface of the door canvase, special armored linings are used, which are fixed from the dwelling side.
Suwald models of locks.
The design of such a lock involves the presence of a secret part, which includes embossed plates that come into operation due to protrusions located on the key.
All Suwalds are interconnected and spring up.
The system of such a lock implies a working condition only when the rotation of the correct key will place the plate in the outer position.
Such structures are very reliable and have increased resistance to the use of physical force. The more the riglels are present, the higher their impact resistance. But in case of damage to the Suwald Castle, the plates can be replaced or a complete dismantling and installing a new lock.
Article on the topic: How to use mirrors in the interior of the living room
But it is worth paying attention to the disadvantage - a large size of a key well. Because of this, with such locks it is easy to cope with the help of the knee. Although more modern models are equipped with additional protection: false grooves, deficiency feature of deficiency, etc.
In any case, the specialist is recommended to use such locks in no one, but in the kit. So increases the safety guarantee of its own dwelling.