Before the construction of the dog booths, you need to decide: what would I like to build, whether it is suitable for a pet for sizes and how it will be in financial defold. It is also necessary to choose the right place where it will be located so that the animal is comfort at any time of the year.
Choosing a place to build booths
The first thing to pay attention is to the direction of the wind, or rather, from where it is most often blowing. The loophole should not be bludging, otherwise the animal will be cold, and rain and snow will fall inside. The booth is better to arrange on a light plot, but it should be a tree or another structure from which there will be a shadow. It is necessary for the summer, in hot weather, the dog could rest not in the heated cone.The dog house should be installed on an exalted place, then flowing water will not be able to accumulate under it. Build a booth on the south side of the plot and close to the entrance to the house. At the same time, the dog should see most of the courtyard and a gate or gate from the conone. This criterion must be observed. Dogs always choose those positions in which they have a maximum review, even if they live in small apartments.
Selection of booth sizes
Before building a dog house with your own hands, you need to decide on its size, as it should be approached by the parameters for an adult dog. Close or, on the contrary, too large a loaf will not be allowed for a pet, it will feel uncomfortable in it.
In the height of the dog's booth, they make 15-20 cm above the height of the dog in the withers (the thickness of the litter is not taken into account). When an animal sits in a cone, it should not get head to the ceiling.
The length of the house is chosen so that it is more by 15 cm than the length of the animal, ranging from the base of the tail, and ending with the nose. The width of the booth is determined by the size of the dog when it lies on the side with the stretched paws. For this make measurements from withers to the tips of the front paws, and add 20 cm. The entrance is made by 5-10 cm less complete growth, and the width is 10 cm wider than the volume of dog breasts.
Article on the topic: how to make a grid for a gazebo with your own hands: Recommendations from the Master
When building booths, you need to focus on the climatic zone of residence. In a warm climate to the size of the house, you can add 5-10 cm to be free and not hot. For the northern regions, Konure is better to entertain thermal insulation materials.
If you can navigate in the breeds of dogs, then the size of the booth can be divided into several groups:
| Breed dimensions | Dimensions of dog coneers, cm (length, width, height) | Input parameters, cm (width, height) |
|---|---|---|
| Small | 70-50-60 | 30-45 |
| Average | 115-80-85 | 40-50 |
| Large | 140-115-100 | 50-70 |
For small breeds of dogs, such as pugs, fees or Pekingese, a loaf will be, as part of the decor for the cottage or apartment.
Drawing up drawing booths
In order not to make a mistake with the calculations during the construction of a dog house with their own hands, you need to make a detailed drawing of the building. It indicates the dimensions of the structure taking into account the animal parameters. It will also help to calculate the desired number of building materials.
Before drawing the drawing, it is necessary to measure the pet in length, in width and to grunt the chest.
Tools and consumables for booths
Wood building materials are best suited for the construction of a dog house. It is from them that you can build a normal building in the microclimate, as the tree has good air circulation.
For work you will need:
- Fireplates.
- Bars - 10 × 10 cm, 10 × 5 cm and 5 × 5 cm.
- Lining or boards, 2 cm thick for walls.
- Roofing material, but not iron.
- Moisture-resistant plywood.
- Mineral insulation.
- Nails or screws.
Thermal insulation materials worth choosing only natural, but not based on fiberglass. Boards must be sharp, without sticking bitch, so that the animal does not hurt.
From construction tools will be required:
- Measuring roulette and pencil.
- Hacksaw.
- Hammer or screwdriver.
If the booth is stained or covered with varnish, then paints are still needed, varnish and tassels.
Construction of dog conery
Choosing what to build a booth should be focused on the dog to be comfortably and safe. According to the appearance of a conserve can be with a vestibule or without it, with a two-tie or a single-sided roof.Construction starts with the preparation of necessary parts, referring to the drawing:
- Brous, 120 cm long - 5 pcs.
- Bruks of 80 cm - 8 pcs.
- Paul boards 8 pcs. - 15 × 80 cm.
- Stands for walls 45 cm - 8 pcs.
- 55 cm rafters - 6 pcs., With speiled angles from 2 sides under 45 °.
- Roof boards 10 pcs. - 15 × 150 cm.
- Moisture-resistant plywood per wall - 120 × 240 cm, 1 sheet, no less than 9 mm thick.
Article on the topic: Lighting shields (SHO)
A broom is used, a cross section of 10 × 10 cm, since the booth by parameters is calculated on a large dog. The walls of the walls can also be made from the boards, 2.5 cm thick. If the insulation of the walls is to be made, then the sheet of plywood will be required to close the thermal insulation material.
Stages of construction:
- The base of the booth is going.
- Mounted walls.
- The roof is manufactured.
- Insulation is carried out.
- It is trimmed with finishing material.
Summer version of a dog house
Collect the booth with your own hands begin with a floor frame. Two bruses of 120 cm and two 80 cm are fixed into a rectangle. To strengthen the frame on its middle, the transverse bar, a long 120 cm. Flooring board flooring. All fasteners (nails, screws) should be attached tightly so that there are no sticking caps and acute ends.
Of the eight racks and bars of 80 cm, the front and rear conera frame is made. In the rear, there are 4 vertical strips at an equal distance. In front of the front with the same four vertical racks, the entrance to the booth is determined. Lases in the coneer can be in the center or shifted to one of the sides. Taking into account the parameters of the pet, the input width is measured. After that, the frames are fixed on the base.
Connect the front and rear walls with two bars of 120 cm, setting them from above. Wall panels made from moisture-resistant plywood are attached to the design of the booths.
From above to the frame at an equal distance, rafters are installed for laying roofing. They are horizontally attached to 5 boards on each side. They are placed from the bottom-up with a small fattest, that is, "tree". The lower boards must be 2,5 cm on the side walls, and from the ends of the house - by 15 cm. The cauldron for summer living or a warm region is ready.
Heated booth
If a dog house will be used in a cold climatic zone, it is recommended to heat insulating it. For this, it will additionally need a bars, natural insulation, a vapor barrier film, a stapler construction, boards (lining or moisture-resistant plywood).
The laying of the heat-insulating material is made after the manufacture of roughing the booth. Bruks on the entire perimeter are attached to the finished base. Their thickness should be no less thermal insulation so that the finishing floor does not tamper the insulation. Steled vapor insulation material and attached with a stapler. The insulation is stacked on top of it and is covered with vapor barrier. After that, the finishing floor is laid.
Article on the topic: How to insulate the inlet metal door with their own hands
Outside the wall of the dog booth is triggered by clapboard. A vapor barrier film is fixed on the inside of the walls. After that, the insulation is installed and is closed with steam insulation with a bracket. Walls from the inside are trimmed with boards or moisture-resistant plywood.
The roof of the booth is also insulated. Above the entrance to the coneer is a dense tissue or silicone canopy, to protect the animal from the wind.
Equipment for confusion in the aviary: Features and advantages
In the aviary for the dog there must be a booth. For regions with a cold climate, a coneer is insulated with natural thermal insulation materials. The roof usually make a single one to be easier to clean inside. The booth is installed on the height of the brick. In front of it make wooden flooring.So that the dog does not freeze even in the coldest days, the booth is equipped with panel or film heaters, and you can also install a cable warm floor.
Infrared panel heaters are convenient and safe to use. They are easily fixed and have a thickness of only 2 cm. The maximum heating temperature is + 50 °, which allows not to close it with a protective frame. The panel is equipped with a thermostat and has good firefighters.
Thanks to the silent type of work, infrared panel heaters will not create the inconvenience of the pet. In addition, they are not afraid of high humidity.
The film heaters have a small consumption of electricity, but at the same time they evenly heatese the surface and do not overcame air. They are mounted so that they are reliably protected from mechanical damage. It should be installed only on a flat surface, and the wire connection locations are carefully isolated.
You can also use heating cables, heating devices on batteries or plug in heating elements (batteries) to central home heating. In the latter case, a protective grid for a heater will be required so that the animal is not injured.
Care for the Booth and how to teach her dog
In the summer you need every month conducts sanitary cleaning of the conera from parasites and dangerous bacteria. The remaining seasons of the year it is enough to get once every 3 months. You can run the dog in the booth only after the complete drying of the drugs.
If the pet does not want to live in a cone, then it needs to be brutal to her. Put inside your favorite toys or delicacies. You can also give food only near the booth.