In addition to its direct functional purpose - the separation of space, interior doors can decorate the room. For example, glass in the interior door can be installed not ordinary transparent, but multicolored or even collect a mosaic pattern.
The interroom door not only shares space, but also adds originality to the interior.
Installing glass at the door can sometimes cause certain difficulties. However, insert the glass on the door itself is possible with a neat execution of the installation sequence. Of course, to perform work on the replacement of glasses in interior doors, you can attract the wizard, but, in addition to the financial costs of work on glazing, you may have to replace the entire door block if the master is a bargan.
Seizure of fragments or old glass
Replacing the glass may be optionally associated with its damage: cracks, divided. It is possible to change the color, the transparency of the glass into the interior door requires the change of the style of the interior of the premises.
But whatever the reason for the installation of the new glass, the dismantling of the old glazing must be extremely careful and gently. In order to ensure the safety of the hands, the dismantling should be performed in gloves from dense, but not thick fabric. In addition to installing glass on the door, you will need:
Diagram of a glazed door: 1. Upper sheet; 2. Lower sheet; 3. Isolation; 4. Rigel for the closer; 5. Glass; 6. Rake for glass; 7. Seal; 8. Sealing mass; 9. Rigel for the rod handle; 10. Loop; 11. Hole under the castle; 12. Korobka; 13. Nickname; 14. Isolation.
- joinery or wide screwdriver;
- small hammer;
- roulette;
- line;
- glass cutter.
In addition, a package of thick paper, as well as a broom and scoop will protect the inhabitants of the house from hitting fragments.
Article on the topic: How to use mirrors in the interior of the living room
It should be pre-examined the method of fastening the glass in the interior door, as it can be varied depending on the manufacturer. Next, you should put on gloves and with the help of the chisels and the hammer it is necessary to loosen the fastenings of the glass. To safely remove the glass, the upper headquarters at first weaken. After that, gently remove the glass.
If the glass is broken in the door, then large fragments should be pulled out, and then start small. All fragments should be folded into a dense bag to avoid injuries around. If not only glass is damaged, but also a rubber gasket, it may be necessary to purchase a rubberized tape.
After all fragments are seized from the interior door, it is necessary to remove the floor with a broom in the place where work was performed. This will allow to protect households from the wounds when walking. Well, the game itself is better to perform in shoes with a solid sole.
Purchase of glass and measurements
Types, shape and location of the doors.
Most often, the glass acquires in stores that specialize on it. They are cut in them according to the size of the customer.
That is why the dimensions of the new glass into the interroom door is a very important point.
Modern production technologies allow you to perform glass of not only different colors, the degree of transparency and relief, but also with the increased characteristics of impact resistance. Therefore, if there are children in the apartment, then you should consider buying just such glass, which will ensure their safety.
After the glass was taken out of the interior door, measurements are performed using a roulette. At the same time it is necessary to take into account the depth of the glass insert in the door leaf and add it to the size to the removed. To do this, use a ruler, which is placed on the whole depth and measured. If this is not done, then the glass will be cut incorrectly and its correct installation will become impossible.
Article on the topic: How to adjust the plastic balcony door: Tips for experienced
Glass Replacement: Recommendations
To insert the glass into the interroom door, you need: sealant, construction gun, new sealing tape, if the old is unsuitable for further use, the stroke, if it is damaged at the moment of dismantling the old glazing. Strapkik should choose or the same color as the door leaf, or a contrasting color, which will additionally select the glass in the interior door. If not found required by the staple, then instead you can use a wax pencil that is sold in a specialized store.
In order to perform the installation of glasses in interroom doors, the door canvas should be removed from the loops and placed horizontally. At the same time, the surface on which the door will be, should be smooth, for example, a long wide table, to which it is placed entirely.
Installation of glass is performed in the following sequence:
Mounting circuit interior doors with glass.
- Using a construction gun, applies a silicone layer for windows and glasses throughout the perimeter of the door leaf, where new glass will be placed.
- The glass is refilled into the gasket, after which it is neatly inserted into the place of attachment. It should not be crushed and hurry: it can cause glass damage. If significant efforts are attached to insert the glass, then it is necessary to cut the gasket in places to the sharp knife to the sharp knife, which clearly do not match the door canvase.
- After installation, the glass is reused with a sealant.
- New or suitable for further use of the headquarters can be fixed using small nails, or using sealant.
- Surplus sealant is removed immediately, not allowing it to be frozen, otherwise it will be difficult to do it.
After Silicone grabbies finally (after about 1-2 hours), the door canvas can be hung on a loop.
Decorative elements that can be placed on glass can be fixed using liquid nails.
But this is done when the door canvas is already naked and tightly fixed. But if this is done before that, but after the sealant is frozen, it turns out more accurately, and the work itself will be more convenient.
Article on the topic: How to make a transition frame for radio with their own hands
If there is a non-standard, unusual glass form in the interior door, then its measurements must be performed especially carefully. In order to achieve perfect accuracy in size, the withdrawn old glass can be attached to the cardboard and cover the contour with a pencil. At the same time, deviations when performing the pattern should not be more than 3-5 mm.
If, in addition, the glass consists of several elements of different color, then these individual parts need to be measured separately and the entire glass canvas. In this case, with the markup of the composite parts and performing new parts of the future glass, the maximum accuracy will be achieved, and when gluing, the required dimensions will be obtained to obtain the end glass.