The glue for the walls of wallpaper can be purchased in any construction store one of the most important problems when sticking wallpaper is the so-called bubbles. Alive air bubbles in this rank with the assembled air bubbles can only join, which are still lying to disperse. Not once the day after repair in the joints of the joints, wallpapers have to put down. What is wrong done? And how to customize the wallpaper when sticking so that these problems do not exactly arise?
Search for reason: why wallpapers are dug at the joints
Find the cause of the problem is the first thing you need to do. Wallpaper lagging behind the wall, and the slit increases between the cloth if the wallpaper was glued, that is, without adhesion. And there are several possible causes of divergence of the bands.
Wallpapers can spacing on the joints as a result of non-compliance with the temperature regime in the room when they are blending.
Why wallpaper diverge:
- The wallpaper glue does not correspond to the material - and therefore, the technique of sticking has already been broken. If the wallpaper is thick, heavy (for example, vinyl, flieslinic, glassy), they need special adhesive with elevated levels of adhesion.
- Sometimes the reason is the poor preparation of the surface under the sticking, and this error can be fixed in time. By and large, all the walls need alignment, putty, primer, but is it always observed all this?
- Disrupted temperature and humidity mode. Drying wallpaper should be in the natural conditions for room, and air humidity should not be more than 70%.
- Another one, a fairly common cause is a long impact of water or steam.
Article on the topic: How to make a bath sustainable
That is, in any case, you need to understand what is the reason for the discrepancy of the canvas in the joints of the joints. Perhaps still, you simply can not properly fit them, and the gaps are very noticeable. If the bands need to be customized in drawing, the unsuccessful fit will be especially visible.
What and how to glue the wallpaper
Today on any construction market you can buy glue, designed specifically for the liner of the joints. Sometimes it will not even be propagally superfluous to smoke joints by this composition. Typically, this glue has a more thick consistency than in conventional adhesive, it is made on the basis of a polyvinyl acetate emulsion.
When sticking wallpaper in the joint, it is recommended to use a roller
Also, this junction glue is characterized by:
- In addition to the emulsion there are additives that can be used in addition to a durable adhesive seam.
- Usually packaging of such adhesive is equipped with a dispenser, some types of compositions, moreover, have a convenient tassel for proper application in hard-to-reach areas.
- Until complete drying, this composition is easy to remove the wet cloth, after polymerization, a transparent waterproof coating is formed.
When you buy such a glue, as in the wallpaper, try not to save. Purchase brands products with good reputation. So fewer risks to acquire a fake, poor-quality composition.
Make it right: how to glue wallpaper so that there is no joints
To infinitely do not loliden the wallpaper so that they do not dug out at all into a spontaneous hour, it is necessary to do everything initially correctly. You can immediately stick the wallpaper so that there is no joints can be seen at all. How is it done? Everything is completely easy.
First, correctly dose the glue. No need it too much, it often takes the edges, which prevents and properly adjust the drawing, and smoke well.
Secondly, be sure to use the roller to stroke the seams. And before this rolling, it will not be superfluous to moisten the wallpaper canvases in places of compounds. There is no difference, dark wallpaper or bright, thick or thin, the risk of jamping the joints is always.
Article on the topic: Balcony Interior in Apartment
Extra pieces of wallpaper can be trimmed with a stationery knife
So, the actions algorithm will be like this:
- Wallpapers cut on the canvas, adding to the length somewhere 5 cm;
- The canvas rinse with glue, sinking glue from the center to the periphery;
- For further impregnation, the canvas can be folded in half;
- Claper wallpaper strictly top down, from the window, you must have a vertical landmark line;
- When the wallpaper was dry completely, the sharp knife is cut off the extra pieces of the canvas;
- The cloth smoothes the wallpaper spatula, the excess glue is cleaned with a dry cloth;
- Once again, pass the roller on the seam, pre-slightly smoem it;
- Similarly, the following canvas and the next canvas are glued, to the previous one, the edges in contact with each other.
Make sure that all windows and windows are closed. That air temperature in the room is not low (optimally - positive 20). After sticking at least 12 hours, or even more, do not open the vents and windows.
Jack or Machine: how to glue paper wallpaper
So all the same how to glue paper wallpaper? Once they were glued only to the mustache, and it was determined by the fact that earlier on the wallpaper there was a special strip, which was stuck in the next web. This allowed exactly sticking the wallpaper, achieving verticalization.
After performing the blending of Wallpaper, the brass should quickly remove the protruding glue
Today, wallpapers are rarely glued to the mustache, especially, taking into account the fact that the drawing should be reduced. Yes, the seams will have to be careful, measure and try. But with a neat sticker, the joints are not visible, and there are no distortions that can happen precisely. But if it is a question of convenience, the popute, as you like more - the main thing is, of course, a good result.
How to glue wallpapers online (video)
If special glue needed for the junctions, why not use them? Moreover, it is not so expensive, the work will be short, but the blending will definitely be high quality. Everything is exactly, firmly, and no discrepancies.
Article on the topic: Top 10 styles for modern bathrooms
Successful sticking!