Plastic windows have long been confidently included in everyday life and are not going to give up their positions primarily because of their reliability and practicality. Despite this, with time, the functionality may violate them.
Do not get upset and look for a specialist to eliminate problems in the work of metal-plastic structures. Adjusting plastic windows independently is quite real.
It is only necessary to explore some of the features of the impacts of the PVC window repair and technologies. Let's try using this article to help figure out how to adjust the plastic design. Here will be presented detailed instructions for the adjustment and repair of plastic window mechanisms.
Types of disorders of PVC structures
How to adjust plastic windows yourself, and what problems can be eliminated without attracting specialists to this? To such violations of the functionality of the plastic window can be attributed:
- Window sash clins the frame;
- The sash is not entirely tight;
- shut-off strings were worn out;
- The design does not close, since the handle is blocked in an open state;
- Do not rotate the handle with a closed sash;
- The handle failed;
- The handle turns badly.
To adjust plastic windows, you will need some tools:
- Passatia;
- hex key 4 mm size;
- Disturbing of different types.
Basic requirements for adjusting windows
Hex key for adjustment
You can adjust the plastic window in several directions. With this feature, you can configure the design of the structure along the frame, as well as to control the degree of its climb.
The technology of adjusting plastic windows is in principle the same, not counting the minor differences in the fittings device of different manufacturers. Now imagine more detailed instructions for adjusting plastic windows on certain work defects.
The sash clins the frame from below
If the sash clings the frame from below, it means the design has saved
After some time the operation of the windows and the doors of PVC, the frame of the frame of the frame is observed. This fact suggests that the design managed to prick.
With such violations, the upper loop of the plastic window is needed. When removing defects in the work of the window sash, it is necessary to move it towards the upper loop and from the bottom up, thus eliminating the sagging. The adjustment scheme is as follows:
- To begin with, open the rod.
- Configure the adjusting screw, which is located next to the top loop in the end of the sash. Perform this process using the hex key, which is rotated clockwise.
- On the bottom loop, the cap is removed and perform a pair of turns clockwise.
- We produce check the degree of adjustment of the sash, and if the defect failed to completely eliminate, perform these steps to the desired result.
Article on the topic: How to rinse from organza: instruction
The coat clins the frame on the side
Adjust the screws with a hex key
Opening PVC windows when the sash touches the frame, pulls the problems. The window device will not be able to freely open and lean. Adjusting the windows with your own hands in the case when the sash clins the frame on the side, produced according to the following algorithm:
- When the frame of the frame flap is only below, it is necessary to move it towards the loop at its lower part. This is achieved by the adjustment screw, which is located under the bottom loop;
- When the frame of the frame of the frame around the perimeter, it is necessary to adjust the screw, which is in the end of the sash next to the top loop.
Setting the shut-off frame
From time to time it is necessary to check the operation of the shut-off strip. Their number is usually so: on one bar from all sides throughout the perimeter.
Independent adjustment of plastic windows is needed, if we notice the wear at least some shut-off plank. This may mean that the device causing. How to correct this disadvantage? You can perform this using such actions:
- Operate the design and remove special plugs from the loops, and use the bolts using the key.
- Go to the upper part, adjusting the screw, so as to adjust the frame horizontally, and then vertically. Adjusting the vertical position of the window is made using the bottom loop screw.
In order to control whether the configuration process is correct, you need to constantly open and close the design. If the sash can open and close freely, the process is completed.
Setting the density of the density of the sash
Zappa regulates the force of the clamp of the frame to the frame
With side on the end of the sash at the place of placement of the handle there is a system of eccentrics or other words of the TsAPF. With the help of them, the clamping of the plastic window is adjusted. The clamp of the design ensures the absence of drafts.
Article on the topic: Salad wallpaper in the interior of the children's room
Each manufacturer has an appearance of eccentrics, but the principle of operation is similar. Adjusting the pin on plastic windows is performed using pliers. For this turn them into several revolutions.
The degree of clamping of the seas in the summer and winter period is different. In the warm time of the year, the clamp should be weaker than in the cold time. In winter, so as not to blow, the sash should be lightened tight.
The adjustment of the clamp can be performed from the loop side, rotating a special screw in the bottom loop. Special attention should be paid to the swivel-flap. Setting the folding mechanism more labor-intensive process.
In this case, you need to adjust the clamp with the screw in the upper loop. The mechanism is located near the hinge. To use them, you need to open the sash, then, pressing the block, arrange the handle to the ventilation mode.
It is possible to properly adjust the screw as follows: with an increase in the degree of climb, the screw is rotated clockwise, when weakening, on the contrary - against the stroke. Do not forget during the configuration process, check the operation of the rotary-folding sash.
Adjusting accessories
We proceed to adjust the accessories of PVC windows. Mostly, for these purposes, screwdrivers and hex key are used. The handles are mainly configured using screwdrivers, and retaliatory strips using a hex key. If the sash is pressed poorly, the bar is shifted towards the street.
The degree of clamp is also configured from the location of the loops, where the mechanism is adjustable using a hexagon key. The degree of clamping is set using the tongue. The more he extends, the better the sash will be pressed. Consider other cases when the window fittings are needed. On the adjustment of the clamping of the sash, see this video:
Setting the handle that has been blocked with open sash
The Eurobon accessories works in this way that when the design is opened, the handle does not rotate to the "closed" position. For this, special blockers are provided in the fitness mechanism.
Article on the topic: Brick laying with your own hands
With certain disorders, the function of the handle may occur when the knob turned in the "closed" position, and the design is open. That is, the blocker fixed the position of the handle. To correct this situation, you must click on the blocking device and turn the locking mechanism to the "open" position.
The handle does not turn
How is the adjustment of plastic windows with their own hands when problems with the handle occurs? It is inspired or executed its turn is impossible.
With such a defect, the grip of the locking mechanism with the response element is not performed. This problem is solved in two ways:
- The sash is shifted using an adjustable screw to the response mechanism;
- The mount is weakened and a plate of dense material is inserted between the sash and the frame.
The handle broke down
If the handle failed, then you can repair plastic windows with your own hands. Repair begins with the fact that the mechanism of the locking device is released by removing the lining.
To do this, it is necessary to delay it a little and turn it on 900. Next, you should turn the mounts with which the device holds, and mount a new handle to its place. For details on adjusting the handle, see this video:
The handle turns badly
Not always needed mechanical adjustment of the accessories of plastic windows. For example, the poor functioning of the plastic window handle occurs mainly due to poor-quality lubrication of the mechanism.
To prevent this, it is recommended to lubricate it annually. To adjust the plastic window with your own hands, and the result pleased you, then you need to follow these rules:
- Regularly check the seals in order to prevent their wear.
- Removing all the plugs, work should be done very carefully, so as not to spoil their appearance.
- If the frame deformation occurred, then the windows cannot be adjusted. In this case, you will have to refer to specialists. PVC windows repair is better not to produce.
An important factor in the long-term functioning of metal-plastic structures, this is the installation of products of generally accepted manufacturers. For example, to establish at home the windows "Rachu", the quality of this product is checked for years. Read more about Adjusting the PVC Window, see this video language:
To avoid the appearance of the defects of the plastic windows, there should be regularly lubricating all rubbing parts.