Laminate creaks: what to do without parsing and how to eliminate

Each laminate owner faced the fact that the material used with time begins to crackle.

If the laminate creaks what to do without parsing? It depends on many factors, but this sound becomes no less annoying.

In particular, it interferes when people aged and very little children live in the house. There are several proven ways, in order to get rid of annoying sound.

Possible causes of outsided sound

This material was originally considered very capricious. In some cases, this type of flooring can be used for decades and at the same time not to cause any difficulties.

Sometimes unpleasant sounds appear a couple of days after its installation. So what if the laminate creaks?

It should be started with the identification of the cause of foreign sounds. Is it worth disassembling or can be eliminated by the cause without exposing the disassembly design. It depends only on what has become the initial cause of such consequences.

Often the cause of creation becomes poor quality

The reason can be:

outdated design of the draft coating;
accumulated garbage;
Low quality material used;
the absence between the walls and coating of the temperature gap;
Laminate creak can due to non-compliance with the established base laying technology;
disorder of individual locking elements;
The substrate may be too thin or thoroughly thick.

Small gap between wall and laminate

Laying laminate, leave a small gap between laminate and wall

Such a clearance must be left to ensure that after installing the coating under the laminate, the creaking appeared. The width of the gap should not exceed 0.7 cm. For large and spacious premises, this indicator may increase to 3 cm.

It will depend on the width of the plinth used. After some time, the laminate will try to take a convenient position for himself, and if it is stumbled upon the absence of free space (gaps), friction will begin between locks, which manifests itself in the form of creak.

Spile the edge of the extreme panels

Sequencing:

disassembling the plinth;
removal of extreme panels;
partial pumping of the edge, the layer of which will be no more than 15 mm; To do this, you can use a hacksaw or an electrolovka;
Installation of all components back to their original place.

If the gap is very insignificant or completely absent, during the expansion of the corners of the material will be characteristic of the plinth and walls.

Sand and garbage

During operation, trash can fall into the space between the planks, which causes friction

Article on the topic: "Three doors" (Tambov) - directory of entrance and interroom doors

During the installation period, special attention should be paid to ensuring that the surface used does not accumulate garbage.

It is recommended to regularly clean the surface of the base, substrate and boards from various dust and other garbage. The vacuum cleaner is suitable as it is impossible.

Also, it should be cut into another, not intended for laying the room.

Possible effects of pollution:

The laminated floor can produce crisp sounds due to the fact that the material used for the manufacture of screed was poor quality;
Such sounds are able to cause not only irritation, but also accelerated wear of the castle compounds;
Sand hit between lock connections will inevitably cause a creaky sound.

Laminate recommend only on perfectly clean surface

Before laying such a material as a laminate, you should more thoroughly clean the surface from various kinds of garbage. If foreign sounds appear directly when moving, then the reason is the massacre of dirt under the layer of laminate.

Since it is very problematic to remove this problem, especially if the main accumulation falls on lock connections, then their safety should be taken in advance.

The new screed will solve the problem of heights and irregularities

The site needs disassembly if the problem lies in an incorrectly made screed. To do this, it will be necessary to pour a new screed (to dissolve, dry, apply a layer of the ground mixture and re-clean it). Only then can be started to install the floor covering. The soil layer will relieve you from the possible sinking of cement in the future.

Clean the surface correctly:

Begin cleaning is necessary with the removal of boards;
A substrate is dismantled;
Laminate creak will begin precisely from the garbage located in it; For this, the surface is cleared with a vacuum cleaner;
A new substrate is installed;
Laminated material is stacked.

What should there be a substrate

Huge substrates are customary to use if there is a need to smooth out irregularities and pits. But from this, your laminate will be crissed even earlier. In this case, the floor creaks just the same from the existing defects associated with the substrate:

Before mounting the coating, make sure that there is sufficient subtleties of this important element; When you ignore this aspect, you may soon need a complete dismantling of the laminated coating;
If the structure of the substrate is thick, it will lead to an additional wire of laminate and a screap;
The permissible thickness of the element is not more than 30 mm.

If the laminate has already started creaking, the coverage is recommended to remove and replace the existing substrate to a thinner design. If you do not have a desire to carry out a complete dismantling of the coating, then it is worth starting to get used to the outsiders.

Not to the end the aligned surface of the base

It is not uncommon that the laminate laminate will be crept due to numerous defects that remained after improper leveling of the base. Possible wine can be called the negligence of the working or purchase of poor-quality materials used to level the base. About what to do if the floors from the laminate publish the creak, see this video:

Article on the topic: High-quality wooden 2-way beam with your own hands

If the laminate is laid without a substrate, disassemble it and laid high-quality coverage

What you need to do is not to creak laminate:

You can install a substrate that allows panels to get into place;
To equalize the use of cycle;
give time to complete the layer grazing;
All irregularities are closed with a mixture based on cement;
It is recommended to align the base on the plot where the creak appeared;
Any irregularity can cause outsiders, so it is necessary to solve the problem immediately after its appearance;
When choosing a laminate, pay special attention precisely base.

Saving funds for the purchase of the required material

One of the most common causes is the desire to save. The poor quality of the floor coating used will not be saved from the screens, even subject to the use of high-quality components under its basis.

The material used must be of the highest quality, proven and manufactured well-known manufacturers. Only such a laminate will differ in the desired level of wear resistance, strength and related quality.

It will be expensive to cost such a laminate, but it will help to save on subsequent repair work and a complete replacement of the coating.

Weak face of poor-quality laminate dilapidated and uneven locks.

What should be paid attention to:

The substrate must have an optimal thickness;
The level of gaps must be observed;
the complete absence of any garbage and dust;
Qualitatively aligned base under the coating.

Unstable room humidity

Maybe after warming up the creation, the creaking will disappear

Such material as a laminate can react to the moisture present in the premises. It is worth considering that the creak will be far from local character, but spread over the entire surface.

What if laminate creaks because of the elevated humidity level in the room? It is not necessary to remove the violets, since after a complete burner of the material they will disappear.

Laminate creaks how to fix:

After changing the season, the creak can go by itself;
If unpleasant sounds appeared in the summer, it is worth waiting for the inclusion of heating; Perhaps after heating the material, the creak will leave;
sometimes cracks during high humidity, which means that these sounds will not be permanent; It is necessary for some time so that the material is mastered in the new conditions, after which all components will be in its place and the sound will disappear.

Is it possible to repair laminate without dismantling

Try to sweep the slots between the planks of the molten paraffin

Real methods of eliminating such defects exist and are not at all imply a dismantling work of the floor covering. First of all, it is necessary to deal with why the surface actually creaks and whether it is in the outdoor coating itself. So how can you get rid of such annoying sounds and at the same time not to disturb the integrity of the coating?

Article on the topic: Instructions for conservation of steam and water boilers

Advice:

Localized creak can be removed using paraffin or based on it; They warm up, after which the screenshots are flooded with wax; Pulling the slots can also be made by wax, which is smeared by slots using a plastic spatula; The spatula can be replaced by an old bank card;
Without parsing, you can get rid of the screenshot by removing individual panels; joints are filled with PVA or mounting foam;
If the creak is localized and is located in the center of the room, you can make several small holes; A glue is introduced into the formed niches using a medical syringe; It is recommended not to step on a renovated area for several days;
The adhesive solution is also used in the "walking" of individual floor elements;
The screech can be removed with the help of oil that flooded holes near the creaking areas;
Various deformations can be rotated using foam; The gaps near the plinth do not touch, but the joints can be subjected to these non-slip manipulations.

You can get rid of hated noise by creating a small lining layer, which is steel under the laminate. This will help slightly align the base, but only if there are no significant irregularities on its surface.

Preventive work

One of the least pleasant defects can be called a creaking of the floor or its individual sections. Subsequently, this can deliver a lot of difficulties up to accelerated coverage.

With the first detection of the defect, it is better to make it easy to eliminate it. Otherwise, you will have to replace all the coating. What happens when laying a laminate without gaps at the walls, see this video:

It is also worth considering a number of such recommendations:

It is worth paying attention to the possible installation of climate equipment, which will adhere to the optimal temperature in the room.
Not only can be saved, but it is necessary, but not on building materials. The product does not have to be expensive, however, to have a good thickness simply.

Place the coating only on the aligned base
The provod must have a sufficiently dense structure and a thickness of at least 0.3 cm. Thick substrates are often the main cause of the screens.
Before laying the material, careful preparatory work should be carried out. It is necessary to align the surface used well and clean it from the construction trash.
Before laying the material for several days is stored indoors.
All key connections must be carefully selected and fit well to each other.
On the perimeter of the room is left a small space.