So that the entrance door always had an attractive view, it is constantly necessary to care for her: paint, putty, etc. In order to protect yourself from excessive troubles, you can do otherwise - to buy Dermantin and put the door cloth to them. In this case, the entire care outside the door will be reduced to wiping its surface with a damp cloth. The upholstery of Dermantine doors with her own hands will also increase its heat and sound insulation, so that your apartment will become more protected and cozy.
Types of materials for upholstery of the entrance door.
Preparatory work
To detect the door to Dermantine, it is necessary to prepare such tools:
- construction stapler;
- roulette;
- a hammer;
- scissors;
- knife;
- screwdriver;
- pliers;
- brush.
From materials should be prepared:
Door upholstery scheme.
- Dermantin. It is a coated material with a width of 1.1-1.4 m wide. To work, you will need a piece of dermantine, the dimensions of which will exceed the dimensions dimensions of approximately 10-15 cm on each side for allowances.
- Lining. As a substrate, a synthet, foam or isolon is perfect. The choice of one or another will depend on your financial capabilities.
- Decorative cord for pulling dermatin.
- Decorative nails. They are made in various colors, so you can easily choose the most suitable option for you.
- Glue. It needs to be purchased if you plan to carry out a metal design.
- Antiseptic. It will be needed for the processing of a wooden canvase.
After everything you need prepared, you can start removing the old coating from the door cloth, and also determine whether you will shoot the door with the loops or not. If you first encounter such finishing work, it is best to remove the cloth and put it on a flat surface . After that, the wooden door is recommended to handle an antiseptic that can protect it from mold and fungus.
Article on the topic: Smokehouse in the country
It should be noted that the door is trimmed only on the one hand, so you need to pay attention to what way it opens. This is due to the fact that roller is formed at the edges of the trim. In some cases, an additional roller uses, with which the door design can be made more sealed.
Wooden door trantine with her own hands
You feed the dermantin on the top edge of the door in several places with nails.After the preparation is finished, you can go directly to finishing work. The first thing from the outdated strips of dermatantine needs to make rollers that are nailed along the edges of the canvas with the front side. They can be hollow or filled with cotton.
Then, on the surface of the door, a layer of thermal insulation material is stacked, on top of which the dermatin itself falls. At the same time, from the loop side, it is necessary to leave the reserve of about 8-9 cm. The edges of the material are separated and nailed with decorative cloves over the entire edge.
Nails should be trigged with no more than 10 cm increments, since otherwise Dermantin will be honest.
Near the loop, the finishing material is rented last. In this part of the door design, a hollow roller is created, which is nailed to the jamb.
In order for the insulation of the door during the operation of the door, Dermantin in several places are dragging with a decorative cord, which is fixed with decorative nails. To give the door of a unique type of cord can be laid in the form of certain drawings. You can apply a pattern in the form of a grid, and you can create a beautiful vignette in the center. The laying of decorative cord is quite a lot. The most popular of them are presented in Fig. one.
Testing metal doors
Figure 1. Options for laying a decorative cord.
The process of finishing the metal design of Dermantine is somewhat different from the foregoing instructions. In many ways, the upholstery of the metal doors is even easier and faster, because there is no need to fix the finishing material with decorative nails. In the process of designing the door, it is this procedure that takes the most time.
Article on the topic: Wall design under TV: design options
First, removed from the loops and the prepared metal door is put on a flat surface and lubricate its edges with glue, after which the thermal insulation material is applied, trying to immediately lay down as it should. The insulation is pressed to the base of the door and give glue to grab, after which the excess material on the sides should be trimmed with scissors.
Next, the ends of the door are treated with adhesive composition and laid the finishing material. This is carried out in this order: first the top is fixed, then go to the side with the loops, then glued the opposite direction, and at the very end the niza is fixed. When installing Dermantina, you need to carefully monitor that it does not bother, and folds were not formed.
After the glue finally dries, the surplus is cut off, and the door is hanging in its place. The door surface can also be decorated with a cord. Only in this case, instead of nails, all the same glue is used to fix it.
Properly performed doors' upholstery will serve you for many years, not only giving all the design an attractive appearance, but also protecting your apartment from third-party noise and heat loss during the cold season.