Nowadays, to save well on heating, many use an additional feature that significantly reduces costs. To distribute the load on the system correctly, a collector for water heat and promoting elements will be required.
History design, as well as the installation work of the floor heating design, according to specialists, is considered a serious event. By installing a collector for a warm floor with your own hands, it should be remembered that each trifle in the installation requires a responsible approach.
Frequently used design schemes
All the flows of the warm floor must be connected to one
The heated design manifold is considered a key node of the device that additionally warms the room.
Vitely, the heatal collector scheme is a certain amount of pipes placed so that all water flows are connected to one.
In the arrangement, only 3 ways of installation of pipes are widely used:
- The installed device on the parallel scheme leads to mixing branches;
- consistent installation method;
- The most difficult version of the device is combined.
Often, with a parallel connection, many heat is lost
How is it better to install a collector of a warm floor with your own hands in a residential room? In the event that the installation of the structure will be installed according to the method of parallel compound, a small heat loss is often performed. With this method, thanks to the device for connecting 2 valves, it is possible to adjust heat.
Setting the floor collector is quite simple. The second method has enhanced performance. The last method is "combined", it has a simple design, in connection with this, the device can be performed personally without additional assistance of experts.
Placement of design departments
The system of the water heat collector device can be made for each heating circuit or make one to all.
In the case of a collector installation, each element of heating should be equipped with a temperature regulator that shows the level of expenses, as well as elements such as:
- Mixer. It is necessary for taking into account the heating degree of the element in the heated circuit.
- The gate lever to perform a container balancing that binds a collector node with a heating structure. The essence of this element is to complete the discovery and closure of the water set.
- The mechanism responsible for stable pressure in the circuit.
Article on the topic: What should be the bedroom
On each heating element there must be a temperature regulator
During the installation period, the connection scheme can be diverse. When the design of a structure, consisting on the basis of one radiator element, a bypass must be present in a mandatory order.
At the same time it is necessary to keep it in the open position. The principle of work is that the excess heat formed began to go immediately into the radiator.
If the inverse view is available in the system, the bypass installation is not required. When heating a small area of the room, the collector device is installed in the secondary element of the system.
Installation of floor collectors of a warm type should be performed with valves installed on the coupling. This is connected with the configuration for its subsequent replacement due to the intensity of work. Having installed in this position, it can be replaced without difficulty.
Principle of working collectors
The essence of the work of collectors for the water heating floor is that water into a heated system is distributed through pipes through its design, which is placed under the floor.
The device of this device is quite simple both in use and in the installation. At the moment when the room is heated, the essence of the work looks like this:
- The liquid, heated to a temperature of 70 degrees, is sent to the collector nodes, bypassing the thermostatic valve.
- A heated liquid comes from the distribution element, as from a thermostatic valve.
- The valve is equipped with a head of a certain value, which allows you to control the heating temperature ranging from 20-70 degrees.
- In the distribution element of the collector node, which is located below the structure, comes the heated liquid, but with a more reduced degree. A small amount of water enters a special distributor, after which it returns to the original position.
- Mixing multiple threads is performed using a special element, and then again it is uniformly distributed over all sections of a warm floor.
- In order for the heating temperature to be transmitted evenly throughout the system, you must install a special element that performs balancing.
- For adjustment work, the flow meter is direct responsibility. Due to this, the adjustment and complete setting of the heating system is performed.
Between the collector cabinet and the floor should remain a distance for bending pipes
It is located nearby the main pipes necessarily at a low height. Also at the time of the cabinet device, it should be remembered that there should be a small distance for the bending of the pipes, which are summarized to the water floor collector. The design of the cabinet can be installed equally both on the wall, and to build a niche.
Install the heating system is simple enough. Even the person who does not have special skills will be able to carry out installation. To make it easier to understand how to assemble a collector for a warm floor, you can use a special instruction:
- To assemble a collector for a warm floor follows from unpacking all items that will be required to install the heating system. In the factory version of the prefabricated design, there are all components, so additionally acquire items will not need.
- Then the heap collector is connected, that is, the connection of all the elements of the pipes and sections is performed.
- Collected into one whole elements of pipes are fixed on the brackets to the wall. After that, perform all connections is much more convenient. Now a visual design of pipes will be a single node.
- All necessary plugs are installed.
- The collector is carried out on the wall. In mandatory, performing the installation of the circulation pump and the valve only after the reinforcement of the collector. Otherwise, the whole process will be associated with inconvenience in the free movement of elements.
- After that, it is connected with its own hands with a warm floor with a heating node of the system. About how to make a warm floor with your own hands, look in this video:
By installing your warm floor, all work must be performed before concreting, otherwise the installation of heating equipment will require additional strokes.
Article on the topic: Calibrator current and voltage