House doors are divided into functional technological use on:
- entrance;
- balcony;
- Interroom.
Classic methods to install doors in wooden houses.
Their installation is practically no different from each other.
Basic requirements for entrance doors in a brusade house are their thermal insulation, sound insulation and durability. To fulfill these requirements, you need to properly install doors. Before starting installation work, it is necessary to carry out exact dimensions and determine the material from which they will be manufactured.
Required tool:
- a hammer;
- Fasteners: screws, nails, selflessness;
- screwdriver;
- hacksaw or circular saw;
- roulette;
- Corolnic;
- plumb;
- level;
- Stuslo;
- putty knife;
- knife;
- electric drill;
- drill.
Installation of doors begins with the assembly of the door block on a flat surface of the table or floor. It is necessary to check the observance of the necessary gaps, mark the places of attachment of mounted loops, handles and locks.
Installation of loops and accessories
Installing the door to the house from the cut.
Entrance doors open up mostly. You should decide which way the door will open, in the left or right. From this depends on the location of the loops and fittings on the doorway and the box.
On the door canvase, from the end, measured and marked with a pencil 250 mm from the top and from Niza. This is the standard height of the location of the loop.
Collect the box. In the sizes of the doorway cut off the pouring bar. At the end ends, an angle of 45 degrees is measured and cut off. The side racks of the boxes are also measured and cut off under 45 degrees. Connect details. Put the canvas and mark the places of fastening the loops on the rack. The gap between the web and the spill bar must be no more than 3 mm.
Milling or chisel to prepare nests for fastening loops. Depth of no more than 3 mm. Mark the point of attachment of the screws and sew shallow holes. It is better to make it better to a thorough attachment by self-drawing, otherwise the material can split, cracks will appear. Disconnecting the loop, fasten them on the canvas and box.
Article on the topic: How to choose a drill: Important criteria and recommendations
When choosing a lock for the door, you need to pay attention to its protection.
Before it is installed, it is necessary to determine the middle axial line on the end of the canvas. Standard installation height of the lock 700-1200 mm. Cutting locks are more likely to enter. By the size of the castle, mark the place of its installation. A chisel to make a recess under the castle. Planck from the castle should be fixed in a floss with an end part of the web.
Scheme of installation of steel door in a wooden house.
Note the exact location of the keyhole. To do this, you can use the sewer. Cut the keyhole. Screw the lock with screws. On the side rack make a mark for attaching a shut-off strip. To do this, turning the key, push the goals and, cover the door, mark the place of its attachment. Choose a chisel material to the height of the shut-off strip. Fasten it.
For mounting the door handle, a hole of a large diameter is dried. By inserting the latch, mark the location of the groove and place of the attachment of the handle. The mill or chisel makes a deepening. Insert the lock - the latch into it. At the same time, the bar must be installed at the end of the door. Marks fix the lock - the latch and screw the handles on both sides. On the jacket make marking for a shut-off strip. The chisel needs to make a groove, equal to the thickness of the plank, and fasten it with screws.
Installation of doors made of wood
A plunder need to check the verticality of the srub walls and mark the place of attachment of the door frame in the opening. Install the box vertically and secure it in the opening wedges. Topper and level check vertical. Scores or dowels to fix the box on top and side. So that the wood does not cracked, when attaching it is necessary to drill holes in advance.
Installation scheme of door loops.
Connecting a loop, hang the door. To check the correctness of the canopy, you must open it several times and close it. Once again, check all the sizes of the necessary gaps - and you can fill in the resulting groove between the opening and the box of the mounting foam. Excess to cut off with a knife. Since this is the entrance door and made of wood, on its perimeter, lay a seal.
Article on the topic: How to choose closers for doors: species, characteristics
Printing modern and beautiful view will help platbands. Measure the desired length and unlock the pouring platband. Cut the corners of 45 degrees from the ends of the board. Help on nails. The same to do with side platbands. Credit lateral and upper platband. Knife to the wall.
Installation of doors - the process is not complicated, but requiring attention.
Installation of a metal door in a brusade house
Installation of doors in a wooden house is carried out no earlier as a year when a complete sediment of the cut will be held.
In the Siruba, built from the bar, you can install the doors at once.
Conduct measurements. At its perimeter, install a casing of solid grade wood, which in the event of a shrink shrink takes on its pressure. The ends of the sprocket and lateral bars cut off the size, the end ends to give an angle of 45 degrees. Connect bars with self-draws.
The casing can be hidden in the ends of the bar in the opening. For this, it is chosen in the size of the bar. To this box, you need to strengthen the door with self-draws. Holes for fastening are drilled in advance. Welding use is not desirable. All grooves and cracks are poured by mounting foam. When it freezes, you cut off the knife too much. The cracks on the threshold are smeared with cement mortar. On the inner surface of the door canvase, the heat-sounding materials are paved. Install the lock and door handles.